Set up the following characteristic equations in the form suited to Evanss root-locus method. Give L(s), a(s), and b(s) and the parameter, K, in terms of the original parameters in each case. Be sure to select K so that a(s) and b(s) are monic in each case and the degree of b(s) is not greater than that of a(s).
a) s + (1/τ) = 0 versus parameter τ
b) s2 + cs + c + 1 = 0 versus parameter c
c) (s + c)3 + A(Ts + 1) = 0
i. versus parameter A
ii. versus parameter T
iii. versus the parameter c, if possible. Say why you can or can not. Can a plot of the roots be drawn versus c for given constant values of A and T by any means at all.
d) 1 + (kp + k1/s + kDs/Ts + 1)G(s) = 0. Assume that G(s) = A c(s)/d(s), where c(s) and d(s) are monic polynomials with the degree of d(s) greater than that of c(s).
i. versus kp
ii. versus kI
iii. versus kD
iv. versus τ

Answers

Answer 1

Answer:

attached below is the detailed solution and answers

Explanation:

Attached below is the detailed solution

C(iii) : versus the parameter C

The parameter C is centered in a nonlinear equation, therefore the standard locus will not apply hence when you use a polynomial solver the roots gotten would be plotted against C

Set Up The Following Characteristic Equations In The Form Suited To Evanss Root-locus Method. Give L(s),
Set Up The Following Characteristic Equations In The Form Suited To Evanss Root-locus Method. Give L(s),
Set Up The Following Characteristic Equations In The Form Suited To Evanss Root-locus Method. Give L(s),
Set Up The Following Characteristic Equations In The Form Suited To Evanss Root-locus Method. Give L(s),
Answer 2

Answer: a(s) is of degree n and b(s) is of degree n-1.

a)Characteristic equation in form suitable for Evans's root-locus method is given by a(s) + b(s)K = 0, where a(s) and b(s) are polynomials of s with real coefficients. Now, given equation can be represented as: s + (1/τ) = 0 => s + (1/τ) = 0s + (1/τ)K = 0=> K = -τs/τ + 0Thus, L(s) = s, a(s) = 1, b(s) = 1 and K = -τ.

b)The characteristic equation is given by:s^2 + cs + c + 1 = 0For the root-locus method, we have to write the characteristic equation in the form a(s) + b(s)K = 0. Since the degree of a(s) is 2, we select K such that the degree of b(s) is also 2, and so b(s) will be monic.s^2 + cs + c + 1 = 0=> (s + c/2)^2 + 1/4 - c^2/4 + c = 0=> s^2 + (2c)s + (1 + c - c^2/4) = 0Now, taking a(s) = s^2 + (2c)s + (1 + c - c^2/4) and b(s) = 1 with K = -1/c^2, we have:a(s) + b(s)K = s^2 + (2c)s + (1 + c - c^2/4) - 1/c^2 = 0

c) The characteristic equation is given by:(s + c)3 + A(Ts + 1) = 0

i. versus parameter A:s = -c is a repeated root of multiplicity 3 when A = 0For s = -c, the characteristic equation becomes:-A(Tc + 1) = 0If A = 0, the characteristic equation will be (s + c)^3 = 0 and will have a repeated root at s = -c with a multiplicity of 3.

ii. versus parameter T:s = -c is a repeated root of multiplicity 3 when T = 0.For s = -c, the characteristic equation becomes:3c^2s + A = 0If A = 0, the characteristic equation will be (s + c)^3 = 0 and will have a repeated root at s = -c with a multiplicity of 3.

iii. versus the parameter c:We cannot draw the root locus of (s + c)3 + A(Ts + 1) = 0 with respect to the parameter c because there is no c term in the characteristic equation; it only contains c cubed.

d) The characteristic equation is given by:1 + (kp + k1/s + kDs/Ts + 1)G(s) = 0Assuming G(s) = Ac(s)/d(s), where c(s) and d(s) are monic polynomials with the degree of d(s) greater than that of c(s), the characteristic equation becomes:

d(s) + kp d(s) + k1 d(s)/s + kDs c(s)/T = 0.

Thus, a(s) = d(s) + k1 d(s)/s and b(s) = kDc(s)/T + kp d(s) with K = -1.

Therefore, a(s) is of degree n and b(s) is of degree n-1.

Learn more about root-locus : https://brainly.com/question/18406313

#SPJ11


Related Questions

Experimental Design Application Production engineers wish to find the optimal process for etching circuit boards quickly. They create a single replicate 24experiment to test the effect of the following factors on time to etch a circuit board: (A) Concentration of nitric acid in the etchant, (B) temperature of the etchant, (C) stirring rate in the etching tank, (D) surface area of the board. Running this experiment, they obtain the data in HW_EDA_137.csv.Preview the document Which factors effects and interaction effects are significant?

Answers

Answer:

Hello your question is incomplete attached below is the missing part and answer

options :

Effect A

Effect B

Effect C

Effect D

Effect AB

Effect AC

Effect AD

Effect BC

Effect BD

Effect CD

Answer :

A  = significant

 B  = significant

C  = Non-significant

D  = Non-significant

AB  = Non-significant

AC  = significant

AD  = Non-significant

BC  = Non-significant

 BD  = Non-significant

 CD = Non-significant

Explanation:

The dependent variable here is Time

Effect of A  = significant

Effect of B  = significant

Effect of C  = Non-significant

Effect of D  = Non-significant

Effect of AB  = Non-significant

Effect of AC  = significant

Effect of AD  = Non-significant

Effect of BC  = Non-significant

Effect of BD  = Non-significant

Effect of CD = Non-significant

(a) At a simple interest rate of 12% per year, determine how long it will take $5000 to increase to twice as much. (b) Compare the time it will take to double if the rate is 20% per year simple interest.

Answers

Explanation:

10000=5000(1.12^x)

2=1.12^x

(log_1.12)(2)=x

x= about 6.1163

10000=5000(1.2^x)

2=1.2^x

(log_1.2)(2)=x

x= about 3.8019

compare them by saying like 20% will be 6.12/3.8 times faster

g At this party, is the fact that a person is from South America independent of that person being majoring in biomedical engineering?

Answers

Answer:

Yes, this is completely independent.

Explanation:

Yes, this is completely independent. Even though there are no South American individuals that are majoring in biomedical engineering in this party it is still a completely independent factor. The origin of birth of an individual does not tie them to a specific degree or field of expertise, therefore a South American individual can study anything they want including mechanical engineering, electrical engineering, or biomedical engineering.

5-81 The shaft is made of A-36 steel and is fixed at end D, while end A is allowed to rotate 0.005 rad when the torque is applied. Determine the torsional reactions at these supports.

Answers

Answer:

The answer is "7.73 kip-ft".

Explanation:

Using this equation, calculate the polar moment of shaft inertia:

[tex]J= \frac{\pi }{32} d^4\\\\[/tex]

  [tex]= \frac{\pi}{ 32} \times 6^4\\\\= 127.234 \ \ in^4[/tex]

Equate the number of moments in x:

[tex]\sum M_x =0[/tex]

[tex]\to T_A-T_B +T_C+T_D =0\\\\\to T_A-40 +20+T_D =0[/tex]

Calculate the torsional response at A using the superposition method:

[tex]\to \phi_A =(\phi_A)_{T} - (\phi_A)_{T_A}\\\\[/tex]

         [tex]= \frac{T_B L_{BC}}{JG}+ \frac{T_C L_{CD}}{JG} - \frac{T_A L_{AD}}{JG}\\\\[/tex]

[tex]0.05= \frac{40 \times 12 \times 2 \times 12}{127.234 \times 11 \times 10^3}+ \frac{20 \times 12 \times 1.5 \times 12 }{127.234 \times 11 \times 10^3} - \frac{T_A \times 12 \times 5 \times 12}{127.234 \times 11 \times 10^3}[/tex]

[tex]0.05= (8.22 \times 10^{-3})+ (3.086 \times 10^{-3})- (5.14 \times 10^{-4} \ T_A)\\\\[/tex]

[tex]\to T_A =12.27 kip \ ft \\\\[/tex]

The torsional answer in help A is  12.27 kip- ft.  It replace the necessary equation values:

[tex]\to T_A-40 +20+T_D =0 \\\\\to 12.27-40+20+T_D=0\\\\T_D=7.73 kip \ ft[/tex]

The torsional reactions at the given supports are;

T_a = 12.3 Kip.ft and T_d = 7.7 Kip.ft

What are Torsional Reactions from Torque?

From the image of the shaft attached, if we take a free body diagram and torsion about x, we will have;

∑Mₓ = 0;

T_a + T_d + 20 - 40 = 0     -----(1)

Using the method of superposition, we have;

Φ_a = (Φ_a)_T - (Φ_a)_T_a

Formula for rotation Φ is;

Φ = TL/(JG)

Thus;

0.005 = [tex][\frac{40 * 12 * 2 * 12}{(\pi/2) *3^{4} * 11 * 10^{3}} + \frac{20 * 12 * 1.5 * 12}{(\pi/2) *3^{4} * 11 * 10^{3}}] - \frac{T_{A} * 12 * 5 * 12}{(\pi/2) *3^{4} * 11 * 10^{3}}[/tex]

Solving for T_a in this gives;

T_a = 12.3 Kip.ft

Thus, from eq 1;

12.3 + T_d + 20 - 40 = 0

T_d = 20 - 12.3

T_d = 7.7 Kip.ft

Read more about Torsional reactions from torque at; https://brainly.com/question/20691242

Don't break or crush mercury-containing lamps because mercury powder may be released.
A) TrueB) False

Answers

A.

It would be released without a doubt so be careful!

Hope this helps :)

Use the Intermediate Value Theorem to show that there is a root of the given equation in the specified interval. Ex = 6 − 5x, (0, 1) The equation ex = 6 − 5x is equivalent to the equation f(x) = ex − 6 + 5x = 0. F(x) is continuous on the interval [0

Answers

Answer:

some part of your question is incomplete

attached below is the complete question

Answer :

F(0) = -5  < 0

F(1) = e - 1 > 0

since the functions : f(0) and f(1) have opposite signs then there is a 'c' whereby F(c) = 0 ( intermediate value theorem fulfilled )

Hence there is a root in the given equation : [tex]e^x = 6 - 5x[/tex]

Explanation:

using Intermediate value Theorem

If F(x) is continuous and f(a) and f(b) have opposite signs then there will be a'c'E (a,b)  whereby F(c) = 0

given equation : [tex]e^x = 6 - 5x[/tex]   on (0,1)

and F(x) = [tex]e^x - 6 + 5x = 0[/tex]

This shows that the F(x) is continuous on (0,1)

F(0) = [tex]e^0 - 6 + 5(0)[/tex]  = -5 which is < 0

F(1) = [tex]e^1 -6 + 5(1)[/tex] = e -1 > 0  and e = 2.7182

since the functions : f(0) and f(1) have opposite signs then there is a 'c' whereby F(c) = 0 ( intermediate value theorem fulfilled )

Hence there is a root in the given equation : [tex]e^x = 6 - 5x[/tex]

An engineer is trying to build a new measurement tool. Which step should the engineer complete first? A. Design a model of the tool to be tested. B. Precisely define the problem that is to be solved. Selected:c. Write a list of the criteria and constraints for the tool.This answer is incorrect. D. Conduct research on how similar problems were solved in the past.

Answers

Answer:

B. Precisely define the problem that is to be solved.

Explanation:

Engineering can be defined as the scientific and technological principles that is used for the design, development, operation and control of tools, machines or equipments, structures and systems. These machines, tools, systems and structures are typically designed and developed for the purpose of solving peculiar problems relating to human life. Simply stated, engineering is focused on proffering solutions to real life problems through a design process.

Generally, the design process comprises of series of steps used for the development of various tools, machines, structures and systems. In a chronological order, the basic steps of a design process are;

1. Define the problem: to proffer a solution to any problem, you have to precisely define the problem that is to be solved. Therefore, this is the first step of the design process.

2. Conduct a research: the engineer should collect or gather data (informations) relating to the project.

3. Brainstorming and analysis of data: this is the stage where the engineer conceptualize his or her ideas.

4. Create a prototype or simulated model of the product.

5. Product analytics and test: this is where the product is being used and tested for any flaw, error or defects. Thus, troubleshooting is also required at this stage.

Hence, if an engineer is trying to build a new measurement tool; the first step the engineer should complete is to precisely define the problem that is to be solved so as to have a good clear-cut understanding of the problem.

in a vehicle you're servicing the fuel pressure drops rapidly when the engine is says that one or more turned off. Technician a says that one or more could be leaking technician b says that a defective check valve in the fuel pump could be the cause who is correct

Answers

Answer:

Both Technicians A and B  are correct

Explanation:

If the fluid pressure will decrease quickly in a car when the ignition says that one or more has been switched off. One or two could be leaking or the source could be a faulty check mechanism in the catalytic converter.

A closed system of mass 20 kg undergoes a process in which there is a heat transfer of 1000 Q6: ki from the system to the surroundings. The work done on the system is 200 kl. If the initial 5 specific internal energy of the system is (250+R:) kl/kg, what is the final specific internal energy, in kj/kg? Neglect changes in kinetic and potential energy:

Answers

The final specific internal energy : 190 kJ/kg

Further explanation  

The laws of thermodynamics 1 state that: energy can be changed but cannot be destroyed or created  

The equation is:  

[tex]\tt E_{in}-E_{out}=\Delta E~system\\\\\Delta E=\Delta U+\Delta KE+\Delta PE\\\\\Delta U=m(U_2-U_1)\\\\Q-W=\Delta U+\Delta KE+\Delta PE[/tex]  

 

Energy owned by the system is expressed as internal energy (U)  

This internal energy can change if it absorbs heat Q (U> 0), or releases heat (U <0). Or the internal energy can change if the system does work or accepts work (W)  

The sign rules for heat and work are set as follows:  

• The system receives heat, Q +  

• The system releases heat, Q -  

• The system does work, W -  

• the system accepts work, W +  

A closed system of mass 20 kg⇒m=20 kg

Heat transfer of 1000 kJ from the system to the surroundings⇒Q=-1000 kJ

The work done on the system is 200 kJ⇒W=+200 kJ

The initial specific internal energy of the system is 250 kJ /kg⇒U₁ = 250 kj/kg

Neglect changes in kinetic and potential energy⇒ΔKE+ΔPE=0, so

Q-W = ΔU

Input in equation

[tex]\tt -1000-200=20(U_2-250)\\\\-1200=20U_2-5000\\\\3800=20U_2\\\\U_2=190~kJ/kg[/tex]

Stack memory is implemented as a stack data structure. Provide the sequence of push and pop operations on stack memory when the collatz method (provided below) is called with n = 5. Note that an enqueue and dequeue is associated with a method call. For example, the first and last operations in the sequence should be push(collatz(4)) and pop(collatz(4)) respectively. public void collatz(int n) { if (n == 1) return; else if (n % 2 == 0) collatz(n / 2); else collatz(3*n + 1); }

Answers

Answer:

attached below is the solution

Explanation:

hello  attached below is the sequence of push and pop operations on stack memory

For The collatz method below

public void collatz(int n) {

if (n == 1) return;

else if (n % 2 == 0)

collatz(n / 2);

else collatz(3*n + 1); }

What motivated software engineers to move from the waterfall model to the incremental or spiral model

Answers

Answer:

1. They needed to develop multiple components in software programs.

2. The ability to overlap the development to be more evolutionary in nature.

3. The need to be more risk-averse or the unwillingness to take risks led to the use of a spiral model.

Explanation:

Software development life cycle (SDLC) can be defined as a strategic process or methodology that defines the key steps or stages for creating and implementing high quality software applications.

In SDLC, a waterfall model can be defined as a process which involves sequentially breaking the software development into linear phases. Thus, the development phase takes a downward flow like a waterfall and as such each phase must be completed before starting another without any overlap in the process.

An incremental model refers to the process in which the requirements or criteria of the software development is divided into many standalone modules until the program is completed.

Also, a spiral model can be defined as an evolutionary SDLC that is risk-driven in nature and typically comprises of both an iterative and a waterfall model. Spiral model of SDLC consist of these phases; planning, risk analysis, engineering and evaluation.

What motivated software engineers to move from the waterfall model to the incremental or spiral model is actually due to the following fact;

They needed to develop multiple components in software programs. The ability to overlap the development to be more evolutionary in nature. The need to be more risk-averse or the unwillingness to take risks led to the use of a spiral model.

Help please all of the numbers b4 the equal sign are wrong

Answers

Answer:

3/5" = 12'1 3/4" = 35'1 1/4" = 25'9/10" = 18'2 13/20" = 53'

Explanation:

One number is wrong; they all lack units.

The basic ratio is 1" = 20', so you can divide feet by 20 to find inches.

3/5" = 12'1 3/4" = 35'1 1/4" = 25'9/10" = 18'2 13/20" = 53'

Perhaps you want decimal inches:

0.60" = 12'1.75" = 35'1.25" = 25'0.90" = 18'2.65" = 53'

Why do the changes to the mass of the planet NOT AFFECT the orbital path of the Planet?

Answers

Answer:

changes of Mass affect the planet because... I'm sorry If this didn't help.

The orbital path of the planet is determined by the balance of the gravitational pull of that planet and the larger body it orbits. Mass does not change the orbital path because the mass that determines this “balance” is the mass of the body the planet is orbiting, not the mass of the planet itself

Under a subsection for geological hazards the buyer is encouraged to obtain an read the booklet

Answers

Answer:

Buyer is encouraged to obtain and read the booklet entitled "The Homeowners Guide to Earthquake Safety." In most cases a questionnaire within the booklet must be completed by Seller and the entire booklet given to the Buyer if the Property was built prior to 1960.

Other Questions
Help plz! I will make you BrainliestPrecipitation is one of the main processes involved in the water cycle. It involves the formation of water falling to the ground from clouds and transforming into either rain, snow, sleet, or hail. Which of the following properties of water can be used to explain why when water falls from clouds it is able to form a rain drop? *A. cohesive abilityB. universal solventC. expansion upon freezingD. moderation of temperature How are humans affected by population growth of other organisms in anarea? How do I solve this?(tangent segment) bird is to fly as snail is to PLEASE HELP!! WILL MARK BRAINLIEST!!~~~Brody is concerned that he is going to exceed the quota set for his mailbox. Where should he go to access the Mailbox Cleanup tools? Backstage view Inbox Deleted Items Folder Outlook Web App BASEBALL & SOFTBALL - ILL GIVE BRAINLIEST 10. ) Match the definition with the correct term.1.scoring a run2.sacrifice bunt3.passed ball, wild pitches and throwing errors4.sacrifice flies5.scoring position6.fielder's choice7.singles, doubles, triples, or homeruns8.grand slam9.walks10.advancing the runners11.stealing a basea.when a catcher, pitcher or fielder makes an error and allows a runner to advanceb.when a batter hits a home run and there are runners on first, second, and third - which will score 4 runs totalc.when a runner touches home plated.types of hits in baseball or softballe.moving the runners from one base to the nextf.when the defense has a choice who to get out. A fielder may choose to get the runner going to third rather than the runner going to first.g.when a runner tries to advance to the next base while the pitcher is throwing to a batterh.when a batter gets 4 balls thrown to him or her OR gets hit by a pitchi.when a batter lays down a bunt to force the defense to throw to first base, allowing another runner on base to advance to the next base into scoring positionj.when a runner is on second or third and could get to home plate if the ball is hit hard or fast enoughk.when a batter hits the ball into the air, a runner that is on base can legally try to go to the next base, but only after the ball has been caught by the fielder Bigham Corporation, an accrual basis calendar year taxpayer, sells its services under 12-month and 24-month contracts. The corporation provides services to each customer every month. On July 1, 2019, Bigham sold the following customer contracts: Length of contract Total Proceeds 12 months $40,000 24 months $80,000 Determine the income to be recognized in taxable income in 2019 and 2020. Length of Contract 2019 Income 2020 Income 12 months $ $ 24 months $ $ How many kids would you like to have in the future? which number produces a rational number when multiplied by 0.5a. square root of 3b. 1/3 (1 over 3)c. 0.555... (0.555 repeating)d. square root of 16 10. -4x + 7 = 15; -2 and tell whether the given number is a solution of each equation Olivia is making bead bracelets for her friends. She can make 3 bracelets in 15 minutes.Write an equation to represent the proportional relationship. Identify the type of figurative language bolded in each quote.". . . shimmied up the trunk of the pear tree and immediately got stuck to it as if with glue.""With a heavy sigh like wind through a tomb.""Medicines are like magic potions." If f(x) = 2x-5 and g(x) = x2 - 4x - 8, find (f+ g)(x).O A. (f+9)(x) = x2 - 2x - 13O B. (f+g)(x) = x2 + 2x - 3O C. (f+g)(x) = x2 - 2x-3O D. (f+g)(x) = 3x2 - 4x - 13 Can someone please help me I need help should the government be responsible for financial safety nets such as social security payments to the retired and insuran Which sentence uses superfluous correctly?A. The water started flowing from the new sprinkler system in a superfluous way. B. The water was supefluous to the runners after the marathon.C. After the power came back on, the use of flashlights was superfluous. D. The new instructor found the class to be superfluous and attentive. Essay on atoms 70 words why do boys say "kk" isn't that supposed to be for girls? Write 310,763,029 expanded form Describe Southern politics