A pump of a water distribution system at 25°C is powered by a 15 kW electric motor whose efficiency is 90 percent. The water flow rate through the pump is 50 L/s. The diameters of the inlet and outlet pipes are both 5 cm and the elevation difference across the pump is negligible. If the absolute pressures at the inlet and outlet of the pump are measured as 100 kPa and 300 kPa, respectively, determine the friction loss in the system.

Answers

Answer 1

The friction loss in the system is 3.480 kilowatts.

Procedure - Friction loss through a pumpPump model

Let suppose that the pump within a distribution system is an open system at steady state, whose mass and energy balances are shown below:

Mass balance

[tex]\dot m_{in}-\dot m_{out} = 0[/tex] (1)

[tex]\dot m_{in} = \frac{\dot V_{in}}{\nu_{in}}[/tex] (2)

[tex]\dot m_{out} = \frac{\dot V_{out}}{\nu_{out}}[/tex] (3)

Energy balance

[tex]\eta \cdot \dot W_{el} + \dot m_{in}\cdot (h_{in}-h_{out}) - \dot W_{f} = 0[/tex] (4)

Where:

[tex]\dot m_{in}[/tex] - Inlet mass flow, in kilograms per second.[tex]\dot m_{out}[/tex] - Outlet mass flow, in kilograms per second. [tex]\dot V_{in}[/tex] - Inlet volume flow, in cubic meters per second. [tex]\dot V_{out}[/tex] - Outlet volume flow, in cubic meters per second. [tex]\nu_{in}[/tex] - Inlet specific volume, in cubic meters per kilogram.[tex]\nu_{out}[/tex] - Outlet specific volume, in cubic meters per kilogram.[tex]\eta[/tex] - Pump efficiency, no unit.[tex]\dot W_{el}[/tex] - Electric motor power, in kilowatts.[tex]h_{in}[/tex] - Inlet specific enthalpy, in kilojoules per kilogram.[tex]h_{out}[/tex] - Outlet specific enthalpy, in kilojoules per kilogram. [tex]\dot W[/tex] - Work losses due to friction, in kilowatts.

Data from steam tables

From steam tables we get the following water properties at inlet and outlet:

Inlet

[tex]p = 100\,kPa[/tex], [tex]T = 25\,^{\circ}C[/tex], [tex]\nu = 0.001003\,\frac{kJ}{kg}[/tex], [tex]h = 104.927\,\frac{kJ}{kg}[/tex], Subcooled liquid

Outlet

[tex]p = 300\,kPa[/tex], [tex]T = 25\,^{\circ}C[/tex], [tex]\nu = 0.001003\,\frac{kJ}{kg}[/tex], [tex]h = 105.128\,\frac{kJ}{kg}[/tex], Subcooled liquid

Calculation of the friction loss in the system

If we know that [tex]\dot V_{in} = 0.05\,\frac{m^{3}}{s}[/tex], [tex]\nu_{in} = 0.001003\,\frac{m^{3}}{kg}[/tex], [tex]h_{in} = 104.927\,\frac{kJ}{kg}[/tex], [tex]h_{out} = 105.128\,\frac{kJ}{kg}[/tex], [tex]\eta = 0.90[/tex] and [tex]\dot W_{el} = 15\,kW[/tex], then the friction loss in the system is:

[tex]\dot W_{f} = \frac{\dot V_{in}}{\nu_{in}}\cdot (h_{in} - h_{out}) + \eta \cdot \dot W_{el}[/tex]

[tex]\dot W_{f} = \left(\frac{0.05\,\frac{m^{3}}{s} }{0.001003\,\frac{m^{3}}{kg} } \right)\cdot \left(104.927\,\frac{kJ}{kg}-105.128\,\frac{kJ}{kg}\right) + (0.90)\cdot (15\,kW)[/tex]

[tex]\dot W_{f} = 3.480\,kW[/tex]

The friction loss in the system is 3.480 kilowatts. [tex]\blacksquare[/tex]

To learn more on pumps, we kindly invite to check this verified question: https://brainly.com/question/544887


Related Questions

Suppose your client wishes to purchase an annuity that pays $50,000 each year for 5 years, with the first payment 4 years from now. At an interest rate of 10%, how much would the client need to invest now? Please round your answer to the nearest hundredth.

Answers

$182,143.58 is the answer

1. What are some pendulum wave characteristics?

2. What are waves characteristics?

3. List characteristics that they both share

Answers

Answer:

     

Explanation:

                                   

Special impact sockets and extensions are easily
identified because they are:
(A) chrome.
(B) aluminum.
(C) flat black
Durant la sto
(D) hard rubber.
les

Answers

Answer:

C

Explanation:

they are flat black

A student borrows $60,000 for business school at 6.5% stated annual interest with equal monthly payments over 10 years. Consider this as a loan with no payments or interest during school so that the problem structure is equivalent to a standard loan received one period before the first payment. How much is the monthly payment?

Answers

Answer:

  $681.29

Explanation:

The amortization formula seems to apply. The monthly payment on a loan of P at rate r for t years is ...

  A = P(r/10)/(1 -(1 +r/12)^(-12t))

For the given loan parameters, the monthly payment is ...

  A = $60,000(0.065/12)/(1 -(1 +0.065/12)^(-12·10)) ≈ $681.29

The monthly payment is $681.29.

i) A sag vertical curve is to be designed to join a 4% grade to a 2% grade. If the design
speed is 50 mi/h, determine the minimum length of the curve. Assume a = 11 ft /sec2 and
perception-reaction time = 2.5 sec. Consider the following criteria:
a) Stopping sight distance
b) Comfort

Answers

Answer:

=4/5 because I'm not going to go back in a year meaning that they are you are

The product of two factors is 4,500. If one of the factors is 90, which is the other factor?

Answers

The other factor is 50
Hope this help <3
Help me and mark my answer as brainliest plz plz

NO LINKS
what was the main drawback of ford's assembly line
A.)the cars broke down quickly
B.)production of the cars required many hours of labor
C.) The cars required a lot of fuel to run
D.)production was not flexible​

Answers

Answer:

D. Im pretty sure at least. you're welcome

Compare the output of full-wave rectifier with and without filter

Answers

Answer:

Full wave rectification flips the negative half cycle of the sine wave to positive so the result is two positive half cycles.

Explanation:

hope it helps a lil

Technician A says that primary vibration is created by slight differences in the inertia of the pistons between top dead center and bottom dead center. Technician B says that secondary vibration is a strong low-frequency vibration caused by the movement of the piston traveling up and down the cylinder. Who is correct? O A. Neither Technician A nor B OB. Technician B O C. Both Technicians A and B D. Technician A​

Answers

Neither technician Technician or  B is correct in the statement above.

What leads to primary vibration?

Vibration is a factor that is said to be caused by one or more other factors that occur together at any given time.

This can be due to actors such as imbalance, misalignment, wear and looseness and others. An imbalance  occurs due to  a "heavy spot" that is found inside a rotating component and it will lead to vibration when the unbalanced weight is said to rotates in circles round the machine's axis.

Learn more about  primary vibration from

https://brainly.com/question/7228243

Write matlab code for motion of a car first order system

Answers

Answer:

Vehicle Dynamics for use with MATLAB/Simulink (VDMS) is a lumped-parameter, 15 degrees-of-freedom vehicle simulation program that reads input files containing chassis, suspension kinematics and compliances, tire, driveline, and aerodynamic inputs.

Explanation:

hope it helps you

determine the values of the forces acting at A and B for the forces system​

Answers

Answer:

You forgot the image and or example. I mean the answer could be anything right now.

8. What are two ways SpaceX plans to change personal travel?

Answers

Answer:

as all the people should go near stratosphere

Which prosses uses a die and press to form parts

Answers

Answer:

stamping

Explanation:

The volume of microbial culture is observed to increase according to the formula
V(m^3)=e^t
where t is time in seconds
a,calculate the expression for V(in^3) in terms of t(minute)
b,

Answers

The expression of V(m³)=e^(t(s)) to make V in in³ and t in minutes is;

V(in³) = (¹/₆₁₀₂₄)a[tex]e^{\frac{1}{60}bt(h)[/tex]

We are given that;

Volume of microbial culture is observed to increase according to the formula;

V = e^(t)

where;

t is in seconds

V is in m³

We want to now express V in in³ and t in minutes.

Now, from conversions;

1 m³ = 61024 in³

Also; 1 second = 1/60 minutes

according to formula for exponential decay, we know that;

V = ae^(bt)

Thus, we have;

61024V = ae^(¹/₆₀b(t(h))

V(in³) = (¹/₆₁₀₂₄)a[tex]e^{\frac{1}{60}bt(h)[/tex]

Read more about subject of formula at; https://brainly.com/question/790938

Explain why power is generated at very high voltages.

Answers

Answer:

It's because to increase efficiency.

Explanation:

As electricity is transmitted over long distances, there are inherent energy losses along the way.

(I hope this will help)

In a modern industrial plant the most likely polyphase power system in use is a/an blank system

Answers

Answer:

  three-phase

Explanation:

2-phase, 3-phase, and 6-phase systems are in use. The most common of these is 3-phase.

A modern industrial plant most likely uses a 3-phase system.

__

Additional comment

Serious research began on 6-phase power transmission systems in 1973. They have been shown to increase power transfer, and to reduce corona, magnetic fields, and audio noise compared to 3-phase systems. However, they are not in widespread industrial use.

When is the output of a NAND-gate HIGH?​

Answers

Answer:

In digital electronics, a NAND gate (NOT-AND) is a logic gate which produces an output which is false only if all its inputs are true; thus its output is complement to that of an AND gate. A LOW (0) output results only if all the inputs to the gate are HIGH (1); if any input is LOW (0), a HIGH (1) output results.

The example of using biotechnology in heart surgery is used to illustrate which of the
following points?
Even advances in biotechnology cannot save every life.
There are many life-saving benefits of biotechnology.
The ethical issues in biotechnology do not apply to surgical fields.
The cost of advances in biotechnology is too high to make this care available to
all.

Answers

Answer:

There are many life-saving benefits of biotechnology.

Explanation:

A periodic digital waveform has a pulse width 25 and a period of 150 . Determine the frequency and the duty cycle

Answers

The frequency  is 6.67 kHz and the duty cycle is:16.67%.

Frequency and duty cycle

Given:

Pulse width=25

Period=150

Frequency:

Frequency=1/(150×10^-6)

Frequency=1/0.00015

Frequency=6.666 kHz

Frequency=6.67 kHz (Approximately)

Duty cycle:

Duty cycle=(25×10^-6)/ (150×10^-6)×100%

Duty cycle=16.67%

Therefore the frequency  is 6.67 kHz and the duty cycle is:16.67%.

Learn more about Frequency and duty cycle here:https://brainly.com/question/16030651

#SPJ1

innovative ideas for civil engineering individual project? I'm running out of time. Need to submit and get approval for this. Please help me and give me a new title to research.
For an egsample- Investigation of replacing Ricehusk instead of Sand in C30, Like wise​

Answers

Answer:

Top Final year projects for civil engineering students

• Geographic Information System using Q-GIS. ...

• Structural and Foundation Analysis. ...

• Construction Project Management & Building Information Modeling. ...

• Tall Building Design. ...

• Seismic Design using SAP2000 & ETABS.

Explanation:

Hope it's help

Determine the mass density of an oil if 0.3 tonnes of the oil occupies a volume of 4m.

Answers

Answer:

Do you mean 4m^3 and 3.0 tones?

Explanation:

solution:

Mass = m = 3.0 tones

- 1 ton = 1,000 kg

= 3.0 × 1,000

= 3,000 kg

volume = v = 4m^3

Required:

Mass density of oil = p = ?

We know that;

[tex]p = \frac{mass}{volume} = \frac{m}{v} = \frac{3000}{4} = 750kg |m^{3} ans [/tex]

The answer is:

750kg / m^3

I need a detailed solution for the multi part question

Answers

Answer:

z=X=c+J=A

Explanation:

The separation and purification process is used for which of the following purposes?
Household cleaning
Developing vaccines
Identifying chromosomes
Documenting chemical reactions

Answers

The separation and purification process is used for DEVELOPING VACCINES. The development of vaccines must follow strict guidelines.

A vaccine is a biological preparation used to protect against harmful diseases (e.g., viruses) in a simple and safe manner.

Vaccine purification is a strict process consisting of clarification, concentration and chromatography in order to separate the extract that contains the active principle of the vaccine.

The techniques used for vaccine filtration include membrane filtration, depth filtration and centrifugation.

Learn more about vaccines here:

https://brainly.com/question/6683555

A full visual analysis would require that a product be dismantled completely so that all of its components can be described.
False
O True

Answers

true, you need to be able to see all parts of the object to visualize it


14. An engine is brought into the shop with a
backfiring problem. Technician A says this
can be the result of a cracked distrib-
Technician B says this problem can
be the result of a faulty carburetor accelerator
pump. Who is right?
problem
utor cap.
he
1.
(A) A only.
(B) B only.
(C) Both A and B.
(D) Neither A nor B.

Answers

Answer:

B. To accurately measure spark advance, use a timing light that incorporates an

ignition advance meter. The spark advance cannot be determined by listening to the way the engine sounds.

Discuss what is an ore.

Answers

Answer:

a naturally occurring solid material from which a metal or valuable mineral can be profitably extracted.

Explanation:

yw

Answer:

Ore is an accumulation of any mineral mixed with other elements. The mineral content of an ore must be in sufficient concentration to make its extraction commercially and economically viable.

Hope it helps.

If you have any query, feel free to ask.

Select the appropriate SDLC process model to develop the VHROM system.

Answers

Software application life cycle simply means the application of standard practices to software applications building.

This is an incomplete information. Therefore, an overview of the software application life cycle will be given. It's the process of planning, creating, testing, and deployment of an information system.

Software application life cycle is divided into six steps which are planing requirements, designing, building, documentation, testing, deployment, and maintenance.

Learn more about software on:

https://brainly.com/question/1538272

What is The output of full-wave rectifier with filter

Answers

Answer:

The output we get from a full-wave rectifier is a pulsating DC voltage that increases to a maximum and then decreases to zero.

Explanation:

hope it helps sorry if im wrong

Cellular network towers are configured in such a way so that they avoid what type of problem?

Answers

avoiding OVERLAP issues

Answer:

They are configured this way to avoid overlap issues.

Explanation:

When is the output of an OR-gate LOW?​

Answers

Answer:

The OR gate is a digital logic gate that implements logical disjunction (∨) from mathematical logic – it behaves according to the truth table above. A HIGH output (1) results if one or both the inputs to the gate are HIGH (1). If neither input is high, a LOW output (0) results.

Other Questions
calculate the exact value of (5/12-11/13)/3/26 Please helppp asapppp due soon ignore the answers i put in their wrong In the early days of the game industry, nearly all games were developed by designers, for designers. More specifically, what age-range/gender were the designers, and for what age-range/gender were they designing the games for? Combine the following expressions 218x^3 - 38x^3A. -xB. 0C.x What is the 13th term of the geometric sequence4, 12, 36, 108, ...? Mrs. Heath baked 56 cookies. She put an equal number of cookies into 7 bags. How many cookies did she put in each bag? Which of the following is classified asM22A large certificates of depositB gold and silverC money market accounts I am confused. NO LINKSWhen you sit up straight for a long time, the __________ holds a lot of your body weight.A. upper backB. lower backC. mid-backD. neckThe person who answers this with the most evidence gets brainliest! Omar just accepted a job at a new company where he will make an annual salary of $52000. Omar was told that for each year he stays with the company, he will be given a salary raise of $4000. How much would Omar make as a salary after 10 years working for the company? What would be his salary after tt years? Part BDiscuss the physical and/or mental health benefits for the different types of exercise that you will be doing over the summer. Remember, you can practice pronunciation for vocabulary by pressing the audio link next to each word in the tutorial. Record your response with your computer's audio recording software, and upload the file when you submit the unit activity to be graded.Your spoken response should include:health benefits for 5-8 sports/activitiescorrect pronunciationa wide variety of vocabulary that you learned from the unit bryan has some 3 cent stamps and some 4 cent stamps. what is the least number of stamps he can combine so the value of the stamps is 33 cents? plz help Solve for x.x+(1.8)=5.37 evaluate the expression for the given value of x.4x+9 for x =9 Match each type of fossil to the description that best matches. Find the value of x. My brother and I used to hate each other we often argued over every thing. Although as we got older.Things got good. I feel like our relationship is good now. Sometimes the old arguments effect our current arguments. As the oldest I defiantly now try to keep the peace. We both adore dogs. Compromising and truly listening have helped our relationship alot.Ill. Revising and Editing Practice: Fix the paragraph below; don't just edit, also revise! ____is a quantity that has magnitude and direction PLZZZ NEED HELP ILL MAKE YOU BRAINLIEST!!!! School taxes for a local district are 2. 5% of a household's income. The smith household earns $80,000 per year. How much do the smiths pay in school taxes per year?. help me plz I need it