Explanation:
it's mean hI small little cute baby girl ...
a 280 nm thin film with index of refraction 1.6 floats on waterwhat is the largest wavelength of reflected light for which constructive interference occur? answer in units of m.
Answer:
Inside the film the wavelength will be λ/n
For constructive interference to occur the film must be λf/4 thick where λf is the wavelength of the light in the film - there will be a 180 degree phase shift at the water/film interface since the index of refraction of the film is greater than that of water - and the light has to travel λ/2 inside the film for constructive interference to occur
280 nm / 1.6 * 4 = 700 nm is the greatest wavelength allowed
Note that 700 nm is also the upper wavelength of the visible spectrum
Paint is an example of which of these?
compound
heterogeneous mixture
homogeneous mixture
none of the above
Answer:
Homogenous Mixture
Explanation:
The composition in paint is uniform so every part of it looks the same throughout the paint.
given how the quantity work—which has units of energy—was defined, another unit for energy, equivalent to the joule (j), is
Answer:
I think you ask for another way of writing the joule (J). It can be expressed as the product between a force applied to a body and the deployment of the body (not necessarily caused by that force applied), so N*m (newton * meter).
The quantity work—which has units of energy—was defined, another unit for energy, equivalent to the joule (j), is Newton ·meter (N· m).
What is unit of physical quantities?The quantity with a constant magnitude that is used to measure the magnitudes of other quantities of the same type is referred to as a unit in physics.
A unit shouldn't alter as time or environmental factors like pressure and temperature change.It ought to be precisely defined.It need to be readily available and repeatable.Unit of work is that of energy, that is, Joule (J).
Again, work = force × displacement
Unit of work = Unit of force × Unit of displacement = Newton . meter (N.m).
Hence, the quantity work—which has units of energy—was defined, another unit for energy, equivalent to the joule (j), is Newton ·meter (N· m).
Learn more about unit here:
https://brainly.com/question/10433377
#SPJ2
a narrow slit is illuminated with sodium yellow light of wavelength 589 nm. if the central maximum extends to ±30.0°, how wide is the slit?
Answer:
because of the gravity of the earth
c. Two persons A and B are pushing a block from opposite sides with
force of 5N and 6N respectively.
[3]
i) Find the magnitude of the resultant force on the block.
ii) Find the direction of resultant force with respect to A and B.
Answer:
1 N
Explanation:
1) You'll just have to sum the force vectors, and since they are opposite, you'll calculate the difference of their magnitudes, in absolute value.
Ftot = |F1 - F2| = 6N - 5N = 1N
2)The direction will be the same as the greater force's direction.
☆ Correct and rewrite the following statements:
a). Rubber is a good conductor of electricity.
b). Electroplating wastes are useful to human health and environment.
c). In an LED bulb, the shorter lead connected to the positive terminal of the battery.
d). pure water conducts electricity.
_______________________
#No spam
#No Internet answers, please
#Explanation needed
Answer:
a) Question:-Rubber is a good conductor of electricity. Answer:-It's incorrect sentence.As we know that, rubber are an insulators of electricity, and they do not not have free ions which can help in conducting electricity.So correct sentence is:
Rubber is a bad conductor of electricity.b)Question:-Electroplating wastes are useful to human health and environment.Answer:-It's incorrect sentence. As we know that, electroplating of substances releases harmful and toxic substances into the environment causing serious health issues in human, so it's waste substances released into environment can have very harmful effects.So correct sentence is:
Electroplating wastes are harmful to human health and environment.c)Question:-In an LED bulb, the shorter lead is connected to the positive terminal of the battery.Answer:-It's incorrect sentence. As we know that, in an LED bulb their are two terminals that is the positive and the negative. So here the lead connected to the positive terminal is always slightly longer than the lead connected to negative terminal of the bulb.So correct sentence is:
In an LED bulb, the longer lead is connected to the positive terminal of the battery.d)Question:-Pure water conducts electricity.Answer:-It's incorrect sentence. As we know that, pure water is a form of H2O where Hydrogen (H) is positive ion and Oxygen (O) is a negative ion which can conduct electricity when they are in individuals but as in pure water they are in combined form of compound H2O in which they become neutral and can't conduct any electricity.So correct sentence is:
Pure water can't conduct electricity.What’s the physics of a football
Answer:
There are many forces involved in the game of football. These are: Force of Gravity, Normal Force, Force of Friction, and Applied Force. Force of Gravity applies to football when the football is thrown or kicked, when a player jumps in the air to avoid a tackle or catch a ball, and is constantly being applied.
Explanation:
How physics is used in football?
When you throw a football across the yard to your friend, you are using physics. You make adjustments for all the factors, such as distance, wind and the weight of the ball. The farther away your friend is, the harder you have to throw the ball, or the steeper the angle of your throw.
PLEASE HELP MEEEEE 80 points on the line and i need this done
Answer:
5) A 200n
F net=0n
6) B 50n
F net=0n
7) C 200n
F net= 900n, up
8) D 80n
F net=60n,left
9) E 300n
F net=60n,left
10)???
11) G 20n
F net=30n,Right
__________________________________
All the answers is hard
correct me if i'm wrong
Definition of main energy level
Answer:
the orbital in which the electron is located relative to the atom's nucleus.
Explanation:
Answer:
the principal energy level of an electron refers to the shell or orbital in which the electron is located relative to the atom's nucleus.
Write AT LEAST 10 SENTENCES based on ONE event that has happened in your life.
Please do it am so tired
Sorry your tired, ill try to make it worth reading.
One day I walked outside, I looked around. THEN BAM a wasp lands right on my face. Its hideously sharp stinger impaled my flesh. I could almost hear it going deeper and deeper. I screamed and ran around in circles until it finely flew away. As I started walking to the door I could feel my heart pules where the thing had stung. I opened the door and went into the bathroom. Right in the middle of my face just above my nose was a red dot, with a slightly less red ring around it, like an ateroid impact. I sat down and went over the entire event five times. I decided to go back outside, as I walked around the corner, another wasp landed on me.
I need help to build a mouse trap race car for my science class and this is my final and these are the materials I have.
So, your science teacher has given your class the classic "mousetrap car" assignment: to make, design, and build a small vehicle powered by the snapping action of a mousetrap to make your car travel as far as possible. If you want to come out ahead of all the other students in your class, you'll need to make your car as efficient as possible so you can squeeze every last inch out of your "car". With the right approach, it's possible to streamline your car's design for maximum distance using only common home materials. You could also buy a mousetrap car kit from any craft store and skip wondering if it will work.
Use large rear wheels. Large wheels have greater rotational inertia than small wheels. In practice, this means that once they start rolling, they're harder to stop rolling. This makes large wheels perfect for distance-based contests — theoretically, they'll accelerate less quickly than smaller wheels, but they'll roll much longer and they'll travel a greater distance overall. So, for maximum distance, make the wheels on the drive axle (the one the mousetrap is tied to, which is usually the rear one) very large. The front wheel is a little less important — it can be large or small. For a classic drag racer look, you'll want big wheels in the back and smaller ones in front.
Use thin, light wheels. Thinner wheels have less friction and may go farther if the distance is what you want or need with your mousetrap racer. It's also important to take the weight of the wheels themselves into account — any unneeded weight will ultimately slow your car down or lead to added friction. In addition, it's worth noting that wide wheels can even have a small negative effect on the car's drag due to air resistance. For these reasons, you'll want to use the thinnest, lightest wheels available for your car.
Old CDs or DVDs work fairly well for this purpose — they're large, thin, and extremely light. In this case, a plumbing washer may be used to reduce the hole size in the middle of the CD (to fit the axle better).
If you have access to old vinyl, these also work extremely well, though they may be too heavy for the smallest mousetraps.
Use a narrow rear axle. Assuming your car is a rear-wheel-drive car, each time your rear axle turns, the rear wheels turn. If your rear axle is extremely skinny, your mousetrap car will be able to turn it more times for the same length of string than it would if it were wider. This translates to turning your rear wheels more times, meaning greater distance! For this reason, it's a wise idea to make your axle out of the skinniest material available that can still support the weight of the frame and wheels.
Narrow wooden dowel rods are a great, easily-accessible choice here. If you have access to thin metal rods, these are even better — when lubricated, they usually have less friction.
Create traction by giving the edges of the friction of the wheels. If the wheels slip against the ground when the trap is sprung, energy is wasted — the mousetrap works to make the wheels turn, but you don't get any extra distance. If this happens with your car, adding a friction-inducing material to the rear wheels may reduce their slippage. To keep your weight requirements down, use only as much as is necessary to give the tips of the wheels some grip and no extra. Some suitable materials are:[1]
Electrical tape
Rubber bands
Additionally, placing a piece of sandpaper under the rear wheels at the start line can reduce slippage as the car begins to move (when it is most likely)
How do you find the final velocity of two objects colliding when you only have the mass and initial velocity of both objects
Answer:
We are required to analyze the conservation of kinetic energy in a perfectly inelastic collision.
kinetic energy:K=1/2mv²
momentum:p=mv
Explanation:
Using the equations for final velocity in terms of masses and initial velocity for a perfectly inelastic collision, work out the final kinetic energy. Calculate the initial kinetic energy and show that kinetic energy is not conserved. Use variables, no numbers
You need to follow law of conservation of energy
Energy is neither created nor destroyedWe know
Kinetic Energy=mass(Velocity)^2You may use momentum formula mass×velocity
In both you need to form equations then solve for final velocity
how to tell a girl you like her?
Scientific notation of 1,750
what is the energy equivalent of an object with a mass of 2.5 kg?
Answer:
2,500g is the answer yes
Use the drop-down menus to complete each statement. Is the process of charging an object without touching it. Is the process of charging a sphere by touching it with a charged rod.
The process of charging an object without touching it is called induction charging.
The process of charging a sphere by touching it with a charged rod is called charging by conduction..
When an uncharged object brings into the contact of the charged object but not touching the object directly, the uncharged object gets charged. This process of charging is called Induction Charging.
When an uncharged object brings in to the contact of the charged object by touching it directly, the uncharged object gets charged, This process of charging is called Conduction Charging.
When a charged rod touches the metal sphere, sphere gets same charged as the rod. The process of charging a sphere by touching it with a charged rod. is called conduction charging.
For more details about the conduction and induction charging, follow the link given below.
https://brainly.com/question/13599143.
Answer:
induction and conduction or 3,2 or c and b
Explanation:
edge 2022
Two spherical balloons are filled with water. The first balloon has a radius of 3 cm, and the second has a radius of 6 cm. How much greater is the volume of water in the larger balloon than in the smaller balloon? Use 3. 14 to approximate pi. Round to the nearest hundredth if necessary. Enter your answer as a decimal in the box.
Answer:
V = 4/3 R^3
V2 / V1 = (R2 / R1)^3 = 2^3 = 8
8.00
The volume of water in the larger balloon is 8 times greater than in the smaller balloon
We'll begin by calculating the volume of each balloon.
For smaller balloon:Radius (r) = 3 cmPi (π) = 3.14Volume (V) =?V = 4/3 πr³
V = 4/3 × 3.14 × 3³
V = 113.04 cm³For larger balloon:Radius (r) = 6 cmPi (π) = 3.14Volume (V) =?V = 4/3 πr³
V = 4/3 × 3.14 × 6³
V = 904.32 cm³Finally, we shall determine how much greater the larger balloon is to the smaller balloon
Volume of smaller balloon = 113.04 cm³Volume of larger balloon = 904.32 cm³Greatness =?Greatness => large / small
Large / small = 904.32 / 113.04
Large / small = 8
Cross multiply
Large = 8 × smallTherefore, the larger balloon is 8 times greater than the smaller balloon.
Learn more on volume of sphere: https://brainly.com/question/9178703
4) What process produces carbon dioxide?
a) photosynthesis
b) replication
c) mutation
d) respiration
5) What happens during cytokinesis?
a) a spindle forms
b) chloroplasts release energy
c) the cytoplasm divides
d) chromosomes
plz answer asap
Answer:
d and c are the answers :)
Your father bought you a pair of shoes. When you wore the shoes you realized there was a problem. The shoes were too long. Why might such prblm arise and how can it be mitigated?
Please answer it soon as possible
Answer: This problem may arise when your father never bought a shoe before. A male is bad at buying accesories and guessing the size, so the mother should have bought a pair of shoes. Or it can also be that your father has a short term memory or that he never knew the size of your feets. The feet might also have irregular growth for which it grows more than the normal size but such cases are rare to be seen.
You can prevent this by going with your father and selecting the shoe of your size. Or you can simply send your mother to buy it for you instead. Or another perfect choice could be is that you just dont ever send your father to buy anything for you or just never buy a pair of shoes. Wear the shoes that you always did or buy it yourself since your the one who is supposed to know the size of your feets. Another possible solution could be that you can make use of the money by gifitng them to someone close to you.
For a uniformly accelerated motion the graph of displacement versus time would be
Explanation:
hope this may help you
have a nice day
1. Which among the sports you stated above are you familiar with?
I am familiar with Russian Mountaineering
Which of the following devices can be red to produce both transverse and
longitudinal waves?
1o) a string
(b) a ripple tank
(c) a helical spring (Slinky (d) a tuning fork
Answer:
Slinky is the correct answer.
Which shows the weight of an atom?
atomic mass
atomic number
chemical symbol
none of the above
Answer:
Atomic mass
Explanation:
Answer:
atomic mass
Click thanks if thankc if this helped
A force f is applied horizontally to block A of mass m1 which is in contact with a block B of mass m2. If the surfaces are frictionless, the force exerted by A on B is given by?
Answer:
Reaction force = Weight
the force exerted by A on B is equal.
M1a = M2a
Explanation: I think the answer is right if wrong message me.
Assuming a current is flowing, what increases the strength of the magnetic field of a coiled electrical wire? Select all that apply. Straightening the wire changing the direction of the current flow adding more coils to the wire placing a metal bar within the coils stopping the current.
The strength of the magnetic field is increased by adding more coils to the wire and placing a metal bar within the coils.
The given problem is based on the concept and fundamentals of the magnetic strength in a current-carrying coil of wire. The current-carrying wire in a coiled form is known as Solenoid.
And the mathematical expression for the magnetic field in a solenoid is,[[tex]B = \dfrac{\mu_{0} \times N \times i}{L}[/tex]
Here,
B is the strength of the magnetic field.
[tex]\mu_{0}[/tex] is the magnetic permeability of free space.
N is the number of coils.
The strength of the magnetic field will increase by increasing the number of coils and placing the metallic slab (it will increase magnetic permeability) within the coils.
Thus, we can conclude that the strength of the magnetic field is increased by adding more coils to the wire and placing a metal bar within the coils.
learn more about the magnetic field here:
https://brainly.com/question/19542022
Answer:
C
Explanation:
Is it raining anywhere else because it is about to start pouring where I live
Current Forecast is:
Sunny with a temp of 67 deg F, as of rn there is no clouds in the sky
Location, Oklahoma USA in the NE corner
which is the hottest and coldest planet in solar system ?
Answer:
hottest plant: vensus, close to the sun
coldest plant: Neptune, farthest from the sun
Explanation:
An object with a mass of 13.2 kg is accelerating at 9.4 m/s? What force is being applied on the object?
Round your answer to the appropriate number of significant figures and use the following formula:
force = mass x acceleration
Force = mass x acceleration:
Force = 13.2 kg x 9.4 m/s
Force = 124.08
Force = 124 Newtons
The force will be = 124 N
What is newton's second law of motion?
Newton's second law is a quantitative description of the changes that a force can produce on the motion of a body. It states that the time rate of change of the momentum of a body is equal in both magnitude and direction to the force imposed on it.
according to newton's second law of motion
Force = mass * acceleration
given
mass = 13.2 kg
acceleration = 9.4 m/s
force = 13.2 * 9.4
= 124.08 N
Rounding off answer to the appropriate number of significant figures
force = 124 N
learn more about newton's second law :
https://brainly.com/question/13447525?referrer=searchResults
#SPJ2
how do you think the liquid density affects the buoyancy of objects placed in the liquid?
Answer:
density can be written as:
d = F / V (weight density) or M / V (mass density)
Since F in the first equation can be written as
B = d V where B is the buoyant force and is proportional to the
weight of the liquid displaced
For a given volume the weight of the liquid displaced is proportional to the density and hence the buoyant force
Help please I will mark you the brainly!
D)
Explanation:
Coz the position changes with time but the position change is not constant throughout time So, D) does not have constant velocity