Answers
Answer:
electrical to thermal and light
(may wanna change the answers)
and the one before that should be electrical to electrical i think
Explanation:
The FitnessGram Pacer Test is a multistage aerobic capacity test that progressively gets more difficult as it continues. The 20 meter pacer test will begin in 30 seconds. Line up at the start. The running speed starts slowly, but gets faster each minute after you hear this signal. A single lap should be completed each time you hear this sound. Remember to run in a straight line, and run as long as possible.
Related Questions
Which would best help a student determine the net force acting on a rollercoaster car as it moves from one point on its track to another?
Answers
Answer:
you can show them a vid
Explanation:
what would the net force be on the box in the problems shown below.( both force and direction). for all four diagrams. please explain answers.
Answers
Answer:
A) object moves 20 N [West] or -20 N [East]
B) object moves 6 N [South] or -6 N [North]
C) object moves 90 N [West] or -90 N [East]
D) object does not move and is at rest*
*Rest means 0
Why:
A)both forces from north and south that are pushing against the object neutralize each other. Assume that north is positive and south is negative: 20 [N] + (-20) [S] = 0
On West and east, you can see that west has a greater force. Assume that west is negative and east is positive: 50 [E] + (-70) [W] = -20 [E]
Need help ASAP plsss
Write 5-6 sentences about
:how do parachutes work ??
Answers
A ripcord system pulls a closing pin, which releases a spring-loaded pilot chute, and opens the container; from which the parachute comes out.
If a skydiver is unable to open her/his parachute, an automatic activation device will automatically open the parachute.
A parachute works by forcing air into the front of it and creating a structured 'wing' under which the canopy pilot can fly. Parachutes are controlled by pulling down on steering lines which change the shape of the wing, cause it to turn, or to increase or decrease its rate of descent.
A ball of mass 4kg moving with a velocity of 20m/s collides with another ball of mass 15kg moving with a velocity of 15m/s in the same direction. Calculate the velocity of the 5kg ball if the collision is perfectly inelastic.
Answers
Answer:
velocity = 16.05 m/s
Explanation:
inelastic collision formula:
m1u1 + m2u2 = (m1 + m2)v
m1 = 4kg
u1 = 20m/s
m2 = 15kg
u2 = 15m/s
find v ?
m1u1 + m2u2 = (m1 + m2)v
(4×20) + (15×15) = (4+15)v
80 + 225 = 19v
305 = 19v
19v = 305
v = 305/19
v = 16.05 m/s
The wavelength of a water wave is 54 m. It has a frequency of 0.03 Hz. What is the velocity of the wave?
Answers
Answer:
1.62 m/s
Explanation:
Wavelength of the water wave= 54 m
The frequency is 0.03 Hz
Therefore the velocity can be calculated as follows
Velocity= frequency × wavelength
= 0.03 × 54
= 1.62 m/s
A hammer strikes a nail with a 10N force for .01 seconds. Calculate the impulse of the hammer
Answers
Answer:
Impulse = 0.1 Kgm/s
Explanation:
Given the following data;
Force, F = 10N
Time, t = 0.01 seconds
To find impulse
An impulse can be defined as the net force acting an object for a very short period of time.
Mathematically, impulse is given by the formula;
Impulse = force * time
Substituting into the equation, we have;
Impulse = 10 * 0.01
Impulse = 0.1 kgm/s
Therefore, the impulse of the hammer is 0.1 kilogram meter per seconds.
The impulse of the hammer is 0.1 Ns.
To solve the given problem we need to use the formula for calculating impulse.
Impulse: This can be defined as the product of force and time on a body.
The formula of impulse is given below.
I = Ft....................... Equation 1
Where :
I = Impulse of the harmerF = Force on the nailt = timeFrom the question,
Given:
F = 10 Nt = 0.01 sSubstitute these values into equation 1
I = 10(0.01)I = 0.1 NsHence, The impulse of the hammer is 0.1 Ns.
Learn more about force here: https://brainly.com/question/13370981
One of the two rectangular components of a force is 20N and it makes an angle of 30
with the force. Find the magnitude of the other components.
Answers
Answer:
11.545NExplanation:
The the horizontal and vertical component be expressed as;
Fx = Fxos theta (horizontal compt)
Given Fx = 20N
theta = 30°
Get F:
20 = Fcos30
20 = 0.8660F
F = 20/0.8660
F = 23.09N
Get the magnitude of the other components. (vertical compt)
Fy = Fsin theta
Fy = 23.09sin30
Fy = 23.09(0.5)
Fy = 11.545N
Hence the magnitude of the other component is 11.545N
10. A 90 kg box is sliding across a surface at a constant velocity while experiencing a rightward applied
force of 40 N. Calculate the force of friction acting on the box.
A. -40N
B. +40N
C.-2.5 N
D. 0 N
Answers
If the box is moving at constant velocity, net force must be zero, so:
F + fr = 0
fr = -F
fr = -40 N
A small sphere of mass m and charge –q is released from rest at point T. If the electric potentials at points S and T are VS and VT, respectively, what is the speed of the sphere when it reaches point S? Ignore the effects of gravity.
(A) 2q/m(Vs + VT)
(B) 4q/m(Vs + VT)
(C) q/2m(Vs - VT)
(D) q/2m (Vs + VT)
(E) 2q/m(Vs - VT)
Answers
Answer:
(E) √[2q/m(Vs - VT)]
Explanation:
Since the charge -q moves from VT to VS, the potential difference is VT - VS.
The work done in moving the charge q across a potential difference V is given by W = qV.
Now, the work done in moving the charge -q across that potential difference VT - VS is thus W = -q(VT - VS) = -q[-(VS - VT)] = q(VS - VT). This work equals the sphere's kinetic energy and kinetic energy equals K = 1/2mv² where m = mass of sphere and v = speed of sphere.
So, K = W
1/2mv² = q(VS - VT)
v² = 2q/m(VS - VT)
taking square root of both sides, we have
v = √[2q/m(Vs - VT)]
the maximum intensity levels of a trumpet, trombone, and a bass drum, each at a distance of 3m are 94 dB, 107dB, and 113dB respectively. What is the intensity level of the three different instruments when played simultaneously, again at 3m?
Answers
Answer:
β = 114 db
Explanation:
The intensity of sound in decibles is
β = 10 log [tex]\frac{I}{I_{o}}[/tex]
in most cases Io is the hearing threshold 1 10-12 W / cm²
let's calculate the intensity of each instrument
I / I₀ = 10 (β / 10)
I = I₀ 10 (β / 10)
trumpet
I1 = 1 10⁻¹² 10 (94/10)
I1 = 2.51 10⁻³ / cm²
Thrombus
I2 = 1 10⁻¹² 10 (107/10)
I2 = 5.01 10-2 W / cm²
low
I3 =1 1-12 (113/10) W/cm²
I3 = 1,995 10-1 W / cm²
when we place the three instruments together their sounds reinforce
I_total = I₁ + I₂ + I₃
I_ttoal = 2.51 10-3 + 5.01 10-2 + 1.995 10-1
I_total = 0.00251 + 0.0501 + 0.1995
I_total = 0.25211 W / cm²
let's bring this amount to the SI system
β = 10 log (0.25211 / 1 10⁻¹²)
β = 114 db
What is net force?
A. The sum of all the forces acting on an object
B. The difference between the largest and smallest forces acting on
an object
C. The largest force acting on an object
D. The smallest force acting on an object
Answers
Answer:
A. The sum of all the forces acting on an object.
Help please I would appreciate it
Answers
Answer:
i think the red runner travels greater distance ie.40 m
Explanation:
although ,the blue one travels 21 m but in the backward direction .so the correct ans is "the red runner travels 40 m"
As a woman walks, her entire weight is momentarily placed on one heel of her high-heeled shoes. Calculate the pressure exerted on the floor by the heel if it has an area of 1.60 cm2 and the woman's mass is 54.0 kg. Express the force in N/m2 and lb/in2. (In the early days of commercial flight, women were not allowed to wear high-heeled shoes because aircraft floors were too thin to resist such large pressures.)
Answers
Answer:
P = 3.3075 x 10⁶ N/m² = 479.71 lb/in²
Explanation:
In order to find the pressure , we first need to find the force exerted by the lady. The force must be equal to the weight of the lady:
Force = F = Weight = mg
F = mg = (54 kg)(9.8 m/s²)
F = 529.2 N
Now, we convert area to S.I unit:
Area = A = (1.6 cm²)(1 m/100 cm)²
A = 1.6 x 10⁻⁴ m²
Now, the pressure can be calculated as:
Pressure = P = F/A
P = 529.2 N/1.6 x 10⁻⁴ m²
P = 3.3075 x 10⁶ N/m²
Now, we convert this into lb/in²:
P = (3.3075 x 10⁶ N/m²)[(0.000145038 lb/in²)/(1 N/m²)
P = 479.71 lb/in²
What energy transformation takes place in the
solar panel?
Answers
calculate the force necessary to keep a mass of 2 kg moving on a circular path of radius 0.2 m with a period of 0.5 second. what is the direction of this force
Answers
1. A 3.8 kg scooter moves with a constant acceleration of 2.5 m/s”. Determine the net
applied force responsible for the acceleration.
Answers
Answer:
9.5 NExplanation:
The force acting on an object given it's mass and acceleration can be found by using the formula
force = mass × acceleration
From the question we have
force = 3.8 × 2.5
We have the final answer as
9.5 NHope this helps you
A pail in a water well is hoisted by means of a frictionless winch, which consists of a spool and a hand crank. When Jill turns the winch at her fastest water-fetching rate, she can lift the pail the 28.0 m to the top in 11.0 s. Calculate the average power supplied by Jill's muscles during the upward ascent. Assume the pail of water when full has a mass of 7.30 kg.
Answers
Answer:
182.28 W
Explanation:
Here ,
m = 7.30 Kg
distance , d= 28.0 m
time , t = 11.0 s
average power supplied = change in potential energy/time
average power supplied = m×g×d/time
average power supplied = 7.30×9.81×28/11
average power supplied = 182.28 W
the average power supplied is 182.28 W
An axe used to split wood is driven into a piece of wood for an input distance of 0.05m. If the mechanical
advantage of the axe is 0.85, how far apart (output distance) is the wood split?
Answers
You have to move your 100 N couch before a delivery company drops off your new one. Unfortunately your roommate is passed out on it. The coefficient of friction between the couch and floor is .43. It takes 250 N of force to get the couch moving. a) How much does your roommate weigh in Newton’s? b) After you get the couch moving it only takes 200 N to keep it moving at a constant speed, what is the coefficient of kinetic friction?
Answers
Answer:
a) Weight of Roommate = 481.4 N
b) μk = 0.34
Explanation:
a)
The force required to move the couch must be equal to the force of friction:
F = frictional force
F = μW
W = F/μ
where,
W = Total Weight of Couch and Roommate
F = Force Required start to move couch = 250 N
μ = coefficient of static friction between couch and floor = 0.43
Therefore,
[tex]W = \frac{250 N}{0.43}\\\\W = 581.4 N[/tex]
So, the total weight is given as:
W = Weight of Couch + Weight of Roommate
Weight of Roommate = W - Weight of Couch
Weight of Roommate = 581.4 N - 100 N
Weight of Roommate = 481.4 N
b)
Now, the force required to keep the couch moving can be given as equal to the kinetic friction force:
F = kinetic friction
F = μk*W
μk = F/W
where,
μk = coefficient of kinetic friction = ?
F = Force required to keep the couch moving = 200 N
Therefore,
μk = 200 N/581.4 N
μk = 0.34
A little girl pushes a 5.0 kg toy baby stroller at constant speed 7.0 m across the floor. She pushes on the handle with a force of 40 N at an angle of 30o with the horizontal. All parts are 4 points each.
Answers
Complete Question
1 a A little girl pushes a 5.0 kg toy baby stroller at constant speed 7.0 m across the floor. She pushes on the handle with a force of 40 N at an angle of 30o with the horizontal. How much work is done by the girl on the wagon?
1b A farmhand pushes 20 ㎏ bale of hay 4m across the floor of the barn if she exerts a horizontal force of 60 N on the hay, how much work is done? (5 pts)
All parts are 4 points each
Answer:
1a
[tex]W = 242.5 \ J[/tex]
1b
[tex]W = 240 \ J[/tex]
Explanation:
Considering question a
From the question we are told that
The mass of the toy baby stroller is [tex]m = 5.0 \ kg[/tex]
The distance covered is [tex]d = 7.0\ m[/tex]
The force the girl applies on the handle is [tex]F = 40 \ N[/tex]
The angle at which this force is applied is [tex]\theta = 30^o[/tex]
Generally the workdone is mathematically represented as
[tex]W = F_x * d[/tex]
Here [tex]F_x[/tex] is the force along the horizontal axis , this is mathematically represented as
[tex]F_x = F cos (\theta )[/tex]
=> [tex]F_x = 40 * cos(30 )[/tex]
=> [tex]F_x = 34.64 \ N[/tex]
So
[tex]W = 34.64 * 7[/tex]
=> [tex]W = 242.5 \ J[/tex]
Considering question b
From the question we are told that
The mass of the toy baby stroller is [tex]m = 20 \ kg[/tex]
The distance covered is [tex]d = 4 \ m[/tex]
The force the girl applies on the handle is [tex]F = 60 \ N[/tex]
Generally the workdone is mathematically represented as
[tex]W = F * d[/tex]
=> [tex]W = 60 * 4[/tex]
=> [tex]W = 240 \ J[/tex]
The rate of change of velocity or speed is known as acceleration. If a car increases it speed form 10 to 20m/s in 2 seconds, then what is its rate of change in velocity?
A) 5 m/s/s
B) 10 m/s/s
C) 20 m/s/s
D) 40 m/s/s
Answers
Answer:
A) 5 m/s/s
Explanation:
Given the following data;
Initial velocity = 10m/s²
Final velocity = 20m/s²
Time, t = 2 seconds.
In physics, acceleration can be defined as the rate of change of the velocity of an object with respect to time.
This simply means that, acceleration is given by the subtraction of initial velocity from the final velocity all over time.
Hence, if we subtract the initial velocity from the final velocity and divide that by the time, we can calculate an object’s acceleration.
Mathematically, acceleration is given by the equation;
[tex]Acceleration, a = \frac{final \; velocity - initial \; velocity}{time}[/tex]
Substituting into the equation, we have;
[tex]Acceleration, a = \frac{20 - 10}{2}[/tex]
[tex]Acceleration, a = \frac{10}{2}[/tex]
Acceleration, a = 5m/s²
what type of friction present when you wrench on a car?
Answers
Answer:Rolling friction is friction that acts on objects when they are rolling over a surface. Rolling friction is much weaker than sliding friction or static friction. This explains why most forms of ground transportation use wheels, including bicycles, cars, 4-wheelers, roller skates, scooters, and skateboards.
Explanation:
What best describes the speed of light waves in solids, liquids, and gases?
The speed is fastest in solids.
The speed is fastest in liquids.
The speed is fastest in gases.
The speed is the same in all matter.
Answers
Answer: It’s fastest in gases. Letter C !
Explanation:
Answer:
its c
Explanation:
if an atom was a scale, in which the nucleus is the size of an apple the electron.....
Answers
Answer:
the nucleus is the size of an apple, approximately 5 cm of radius e, the atom has a radius of R = 5 cm 104 = 50000 cm = 50 km
Explanation:
In the Rutherford experiments it was proved that the atomic nucleus has the volume 10-4 the volume of the atom.
If we make a scale design in which the nucleus is the size of an apple, approximately 5 cm of radius e, the atom has a radius of R = 5 cm 104 = 50000 cm = 50 km
This shows that almost the entire volume of the atom is empty.
a machine
of efficiency of 70% is used to raise
a body of
mass 80 kg through
a vertical distance of 3m in
40 seconds. Calculate the power input. (Take g = 10 m/s²)
Answers
Answer:
Power_input = 85.71 [W]
Explanation:
To be able to solve this problem we must first find the work done. Work is defined as the product of force by distance.
[tex]W = F*d[/tex]
where:
W = work [J] (units of Joules)
F = force [N] (units of Newton)
d = distance [m]
We need to bear in mind that the force can be calculated by multiplying the mass by the gravity acceleration.
Now replacing:
[tex]W = (80*10)*3\\W = 2400 [J][/tex]
Power is defined as the work done over a certain time. In this way by means of the following formula, we can calculate the required power.
[tex]P=\frac{W}{t}[/tex]
where:
P = power [W] (units of watts)
W = work [J]
t = time = 40 [s]
[tex]P = 2400/40\\P = 60 [W][/tex]
The calculated power is the required power. Now as we have the efficiency of the machine, we can calculate the power that is introduced, to be able to do that work.
[tex]Effic=0.7\\Effic=P_{required}/P_{introduced}\\P_{introduced}=60/0.7\\P_{introduced}=85.71[W][/tex]
. A pendulum of length l = 9.8 m hangs in equilibrium and is then given velocity
v
=0.2
m/s at its lowest point. What is the amplitude of the subsequent oscillation?
Answers
Answer:
the amplitude of the sequence oscillation=
ASO = length × velocity
= 9.8 × 0.2 = 19.6
ASO = 19.6
Some metals have a molecular structure that makes them good conductors. Explain how understanding this relationship can help engineers make more powerful batteries.
Answers
Answer:
Explained below.
Explanation:
Conductors can be defined as materials that permit electricity to flow through them easily.
Now, metals have a molecular structure that makes them good conductors because electrons in the atoms of these conductors tend to move freely from one atom to the other. So a majority of metals make good conductors because these metals tend to hold their electrons loosely. In short, it can help engineers make powerful batteries because then it means that they are capable of giving much more electrical energy since nowadays, advanced batteries make use of ion charges for the batteries.
The technology in the picture produces which energy conversion?
A. Chemical energy to kinetic energy
B. Thermal energy to kinetic energy
C. Light energy to electrical energy
D. Kinetic energy to electrical energy
Answers
Answer:
D
Explanation:
because the whole town needs to be powered through some sort of energy and kinetic energy means the movement of something
The technology in the picture represents the conversion of kinetic energy to electrical energy. So, the correct option is D.
What is meant by kinetic energy ?Kinetic energy of a body is defined as the energy acquired by the body due to the virtue of its motion.
Here,
The given picture represents the dam system at a town.
We know, according to conservation of energy, energy can neither be created nor be destroyed, but can be transferred from one form to another.
In the dam system, the application of conservation of energy is implemented.
Dam consists of a water stream and turbines. The water stream is arranged in such a way that, when the water is running from a height, the water acquires an energy in the form of kinetic energy.
This kinetic energy of the water is converted to electrical energy with the help of the turbines, which are rotating continuously and thus electricity is produced.
Hence,
The technology in the picture represents the conversion of kinetic energy to electrical energy.
To learn more about kinetic energy, click:
https://brainly.com/question/999862
#SPJ7
A stunt person jumps from the roof of a tall building, but no injury occurs because the person lands on a large, air-filled bag. Which one of the following best describes why no injury occurs?
A. The bag increases the amount of time during which the momentum is changing and reduces the average force on the person.
B. The bag increases the amount of time the force acts on the person and reduces the change in momentum.
C. The bag reduces the impulse to the person.
D. The bag provides the necessary force to stop the person.
E. The bag decreases the amount of time during which the momentum is changing and reduces the average force on the person.
Answers
Answer:
A stunt person jumps from the roof of a tall building, but no injury occurs because the person lands on a large, air-filled bag. Which one of the following best describes why no injury occurs?
The bag increases the amount of time during which the momentum is changing and reduces the average force on the person.
ANSWER: A
Answer:
A. The bag increases the amount of time during which the momentum is changing and reduces the average force on the person.
During stunts, people usually put an-air filled bag on the ground for safe landing and to prevent injuries.
Momentum is calculated by m* v where m is for mass and v is for velocity.
Force is directly proportional to momentum
F∝M
The bag in this scenario helps to increases the amount of time the force acts on the person. This implication means that there is a reduction in the change of momentum. Since Force and momentum have a directly proportional relationship then the Force taken to hit the floor is greatly reduced.
Read more on https://brainly.com/question/20362316
Mark all the units for speed
Answers
Answer:
Speed. I am speed.
Explanation:
The FitnessGram Pacer Test is a multistage aerobic capacity test that progressively gets more difficult as it continues. The 20 meter pacer test will begin in 30 seconds. Line up at the start. The running speed starts slowly, but gets faster each minute after you hear this signal. A single lap should be completed each time you hear this sound. Remember to run in a straight line, and run as long as possible.