Label the following statements as either T (true) or F (false).
1) For Propane (C3H8) burning with theoretical amount of air, the air-fule ratio on the mole basis is 5.
2) The enthalpy of any substance at the standard reference state is 0.
3) 180% of theoretical air is equivalent to 80% of excess air.
4) The conservation of mass principle requires that the total number of moles on each side of a chemical reaction is equal.
5) The adiabatic flame temperature of methane (CH4) burning with pure oxygen and theoretical amount of air is the same, all other conditions being the same.

Answer:

Battery Voltage

Voltage refers to the amount of electrical potential your battery holds. The standard automotive battery in today's vehicles is a 12-volt battery. Each battery has six cells, each with 2.1 volts at full charge. A car battery is considered fully charged at 12.6 volts or higher.

Answer:

Alternator

Explanation:

A device which converts mechanical energy into electrical energy.

I hope it helps.

Answer:

Explanation:

Galvanic corrosion occurs when two dissimilar metals are immersed in a conductive solution and are electrically connected. One metal (the cathode) is protected, whilst the other (the anode) is corroded. The rate of attack on the anode is accelerated, compared to the rate when the metal is uncoupled.

Answer:

  4.5 m/s = 16.2 km/h

Explanation:

The speed is the ratio of distance to time:

  speed = (180 m)/(40 s) = 4.5 m/s

The correct responses are;

(i) Weight percent of nitrogen: 58.6%

Weight percent of oxygen: 14.65%

Weight percent of carbon dioxide: 29.59%

(ii) Volume percent of nitrogen: 64.38%

Weight percent of oxygen: 14.1%

Weight percent of carbon dioxide: 21.53%

(iii) Partial pressure of nitrogen: 19.314 psia

Partial pressure of oxygen: 4.23 psia

Partial pressure of carbon dioxide: 6.459 psia

(iv) Partial pressure of nitrogen: 19.314 psia

Partial pressure of oxygen: 4.23 psia

Partial pressure of carbon dioxide: 6.459 psia

(v) The average molecular weight is approximately 32.02 g/mole

(vi) At 20 psia, 60 °F, the density is 0.11275 lb/ft.³

At 14.7 psia, 60 °F, the density is 0.0844 lb/ft.³

At 14.7 psia, 32 °F, the density is 0.0892 lb/ft.³

(vii) The specific gravity of the mixture 0.169

Reasons:

The volume of the tank = 40 ft.³ = 1.132675 m³

Content of the tank = Carbon dioxide and air

The pressure inside the tank = 30 psia = 206843 Pa

The temperature of the tank = 70 °F ≈ 294.2611 K

Mass of carbon dioxide placed in the tank = 2 lb.

Percent of nitrogen in the tank = 80%

Percent of oxygen in the tank = 20%

(i) 2 lb ≈ 907.1847 g

Molar mass of carbon dioxide = 44.01 g/mol

Number of moles of carbon dioxide = [tex]\displaystyle \mathbf{ \frac{907.1847 \, g}{44.01 \, g/mol}} \approx 20.613 \, moles[/tex]

Assuming the gas is an ideal gas, we have;

[tex]\displaystyle n = \mathbf{\frac{206843\times 1.132674}{8.314 \times 294.2611} }\approx 95.7588[/tex]

The number of moles of nitrogen and oxygen = 95.7588 - 20.613 = 75.1458

Let x represent the mass of air in the mixture, we have;

[tex]\displaystyle \mathbf{ \frac{0.8 \cdot x}{28.014} + \frac{0.2 \cdot x}{32}}= 75.1458[/tex]

Solving gives;

x ≈ 2158.92 grams

Mass of the mixture = 2158.92 g + 907.1847 g ≈ 3066.1047 g

[tex]\displaystyle Weight \ percent \ of \ nitrogen= \frac{0.8 \times 2158.92}{3066.105} \times 100 \approx \underline{58.6 \%}[/tex]

[tex]\displaystyle Weight \ percent \ of \ oxygen = \frac{0.8 \times 2158.92}{3066.105} \times 100 \approx \underline{14.65\%}[/tex]

[tex]\displaystyle Weight \ percent \ of \ carbon \ dioxide = \frac{907.184}{3066.105} \times 100 \approx \underline{29.59\%}[/tex]

ii.

[tex]\displaystyle Number \ of \ moles \ nitrogen= \frac{0.8 \times 2158.92 \, g}{28.014 \, g/mol} \approx 61.65\, moles[/tex]

[tex]\displaystyle Number \ of \ moles \ oxygen= \frac{0.2 \times 2158.92 \, g}{32 \, g/mol} \approx 13.5\, moles[/tex]

Number of moles of carbon dioxide = 20.613 moles

Sum = 61.65 moles + 13.5 moles + 20.613 moles ≈ 95.763 moles

In an ideal gas, the volume is equal to the mole fraction

[tex]\displaystyle Volume \ percent \ of \ nitrogen= \frac{61.65}{95.763} \times 100 \approx \underline{64.38 \%}[/tex]

[tex]\displaystyle Volume \ percent \ of \ oxygen = \frac{13.5}{95.763} \times 100 \approx \underline{14.1\%}[/tex]

[tex]\displaystyle Volume \ percent \ of \ carbon \ dioxide = \frac{20.613 }{95.763} \times 100 \approx \underline{21.53\%}[/tex]

(iv) The partial pressure of a gas in a mixture, [tex]P_A = \mathbf{X_A \cdot P_{total}}[/tex]

Partial pressure of nitrogen, [tex]P_{N_2}[/tex] = 0.6438 × 30 psia ≈ 19.314 psia

Partial pressure of oxygen, [tex]P_{O_2}[/tex] = 0.141 × 30 psia ≈ 4.23 psia

Partial pressure of carbon dioxide, [tex]P_{CO_2}[/tex] = 0.2153 × 30 psia ≈ 6.459 psia

(v) The average molecular weight is given as follows;

[tex]\displaystyle Average \ molecular \ weight = \frac{3066.105\, g}{95.7588 \, moles} = 32.02 \, g/mole[/tex]

(vi) At 20 psia 70 °F, we have;

Converting to SI units, we have;

[tex]\displaystyle n = \frac{137895.1456\times 1.132674}{8.314 \times 294.2611} \approx 63.84[/tex]

The number of moles, n ≈ 63.84 moles

The mass = 63.84 moles × 32.02 g/mol  ≈ 2044.16 grams ≈ 4.51 lb

[tex]\displaystyle Density = \frac{4.51\ lb}{40 \ ft.^3} \approx \underline{0.11275\, lb/ft.^3}[/tex]

When the pressure is 14.7 psia = 101352.93 Pa, and 60 °F

[tex]\displaystyle n = \frac{101352.9\times 1.132674}{8.314 \times 288.7056} \approx 42.8247[/tex]

The mass = 47.8247 moles × 32.02 g/mol  ≈ 1531.35 grams = 3.376 lb.

[tex]\displaystyle Density = \frac{3.376 \ lb}{40 \ ft.^3} \approx \underline{ 0.0844\, lb/ft.^3}[/tex]

When the pressure is 14.7 psia = 101352.93 and 32 °F

[tex]\displaystyle n = \frac{101352.9\times 1.132674}{8.314 \times 273.15} \approx 50.5482[/tex]

The mass = 50.5482 moles × 32.02 g/mol  ≈ 1618.55 grams = 3.568 lb.

[tex]\displaystyle Density = \frac{3.568 \ lb}{40 \ ft.^3} \approx \underline{ 0.0892 \, lb/ft.^3}[/tex]

(vii) [tex]\displaystyle The \ specific \ gravity \ of \ the \ mixture \ = \frac{\frac{3066.1047\, g}{40 \, ft.^3} }{1.00} = \frac{\frac{6.7596 \, lbs}{40 \, ft.^3} }{1.00} \approx \underline{0.169}[/tex]

Learn more about partial pressure here:

https://brainly.com/question/19813237

Answer:

umm okay for starters I have no clue lol.

what is aerodynamics????

Answer:

False

Explanation:

I can say it oxidizes gas pollutants such as hydrocarbons and carbon monoxide. It also reduces nitrogen oxides into water, hydrogen, and carbon dioxide.

Answer:

you know you could use like quora or yahoo answers

Answer: The elastic modulus and flexural strength are found to decrease with increased porosity. Fractography studies have been undertaken to identify the role of the pores on the fracture path. The deflection and cracking behavior of concrete structure depend on the flexural tensile strength of concrete. Many factors have been shown to influence the flexural tensile strength of concrete, particularly the level of stress, size, age and confinement to concrete flexure member, etc.

Explanation:

Answer: identify your decision. relize you need to make a decision.

Explanation:

The three most common software development methods are the Waterfall Approach, the Incremental Approach, and the SPIRAL Approach. These methods depend on the team size and specific goals.

Software development is the sequential procedure that involves the division of the work into smaller and parallel stages in order to improve software design and product management.

The software development methods depend on both the team size and specific objectives.

The most common methodologies for software development include:

Learn more about software development here:

https://brainly.com/question/14275830

Answer:

the answer I know is A. different substances. hope this helps :).

Explanation:

just always study hard and God bless.

Answer: Well, that's a good question. When we look around us, we tend to see what technology has done for us, and how far it is taking us. It might be disruptive, but without it there would be no high tech military weapons, and then how would we defend ourselves? There would be no technology entertainment and without that, life would be very dull. In answering your question, we can be thankful for what it is and how far it has been taking us in life.

Explanation: Please mark a brainliest if correct it helps and have meery holidays!

Answer:

manager and supervisor

Explanation:

Answer:

17A) 52mm

17B) 132mm

17C) 67mm

18.) 34

Explanation:

For 17)

Each distance is determined by the total distances surrounding it. For example, 17A is 73mm - 21mm, which is 52mm.

For 18)

Set up the problem as an algebraic expression:

a + b + c + d = 115

Since you know 3 of the values, you can plug them in and subtract them from 115, which turns into 34.

Answer:

  B. 10,000 ohms

Explanation:

|8000 +j6000| = √(8000² +6000²) = 1000√(64 +36) = 1000√100 = 10,000

The impedance is 10,000 ohms.

Answer:

I think it would be C but im not sure sorry if its wrong

The first case where the power of synthesis was applied was in Chile when they had to put 100 families in houses around 40m².

It should be noted that the power of architecture is the fact that it can synthesize a complex entry to a problem.

Chilean architect Alejandro used this in building more than several houses for the poorest communities in Chile. His rigorous and innovative design approach used a social framework that laid a precedent within the profession.

During this period in Chile, a normal middle-class home was about 80m² but he built his in 40m² and it was a good home that managed the resources that were available.

Learn more about synthesis on:

https://brainly.com/question/884041

Answer:

4.25

Explanation:

The mean deviation is how far, on average, all values are from the middle. To do that, we subtract each element from the mean of the elements, take their absolute values, and then divide by the number of elements in the set. Here's the formula: [tex]\sum\frac{|x-\mu|}{n}[/tex]

Here the mean is 9.5, the count n = 8, so the mean deviation is 4.25

Answer: It does make sense, because I've been involved in these careers and have a long family line of them. And other questions?

Explanation:

Answer:

oh this happened with me to ,this will be alright just wait a bit

A CNC machine stands for Computer Numerically Controlled Machine, they are used to Machine objects in hence create items, machine parts from prototypes. Hence the CNC machines are not used for testing/Analysis

D. CNC machines.

In Engineering the following items are basically needed for and during test/Analysis

Learn more:

https://brainly.com/question/9275741

Answer:

Technician A says that primary vibration is created by slight differences in the inertia of the pistons between top dead center and bottom dead center. Technician B says that secondary vibration is a strong low-frequency vibration caused by the movement of the piston traveling up and down the cylinder. Who is correct? O A. Neither Technician A nor B OB. Technician B O C. Both Technicians A and B D. Technician A​

Explanation:

Technician A says that primary vibration is created by slight differences in the inertia of the pistons between top dead center and bottom dead center. Technician B says that secondary vibration is a strong low-frequency vibration caused by the movement of the piston traveling up and down the cylinder. Who is correct? O A. Neither Technician A nor B OB. Technician B O C. Both Technicians A and B D. Technician A​

Answer:

a. Commutator:

the commutator reverses the current direction with each turn serving as a mechanical rectifier to convert the alternating current from the windings to unidirectional direct current in the external load circuit.

b. Armature core

Armature core is a physical structure made up of silicon steel stampings. The core is laminated to keep iron losses low. Armature winding is the main current carrying winding where we either provide(electric supply to motor) or extract e.m.f(collect electric power from generator).

c. Field system

The field winding basically form an electromagnet, that produces field flux within which the rotor armature of the DC motor rotates, and results in the effective flux cutting

d. Brushes

The function of brushes is that the brushes conduct current between stationary wires and moving parts of the electric Generator.

e. Armature winding

The winding wound on the core is given current through a DC supply. This current-carrying winding as under the influence of the magnetic field develops a force that develops a rotational torque. This torque enables the machine to rotate.

[tex] \bold \pink{ \underline{hope \: it \: helps}}[/tex]