The charge with uniform density 15.9 nC/m^2 everywhere on its surface is 4.8nC, on its curved lateral surface only is 582.5nC, throughout the plastic is 1730.6nC, along the length of the plastic is 174.7nC.
Given the radius of cylinder (r) = 2.55cm = 2.55 x 10^-2m
The length of cylinder (h) = 6.24cm = 6.24 x 10^-2m
The total surface area of cylinder is calculated as: (A) = 2πr(r + h)
Then, A = 2 x 3.14 x 2.55 x 10^-2(2.55 x 10^-2 + 6.24 x 10^-2)
A = 188.8 x 10^-4m^2
The charge on cylinder = q
We know that the charge density is calculated as:
charge = charge density x total area of cylinder
(a) Given the charge density on cylinder a is = 15.9NC/m^2
The charge on cylinder = surface area x charge density
charge = 4πr^2 x 15.9 = 4 x 3.14 x (2.55 x 10^-2)^2 x 15.9 = 4.8nC
(b) the charge density on curved lateral surface only = 15.9nC/m^2
charge = 2πrhx15.9 = 2 x 3.14 x 2.55 x 10^-2 x 6.24 x 10^-2 x 15.9
= 582.5 nC
(c) the charge density throughout the plastic is = 475 nC/m^3
charge = πr^2h x 475 = 1730.6 nC
(d) along the length of the plastic is 64.2 nC/m
charge = πrh x 64.2 = 174.7 nC
To learn more about charge click here https://brainly.com/question/30163160
#SPJ4
complete question: four solid plastic cylinders all have radius 2.55 cm and length 6.24 cm. find the charge of each cylinder given the following additional information about each one.
Cylinder (a) carries charge with uniform density 15.9 nC/m^2 everywhere on its surface.
Cylinder (b) carries charge with uniform density 15.9 nC/m^2 on its curved lateral surface only.
Cylinder (c) carries charge with uniform density 475 nC/m^3 throughout the plastic.
Cylinder (d) carries charge with uniform linear density 64.2 nC/m along the length of the plastic.
a cup of hot tea initially at 95*c, cools to 75*c, in 5.0 minutes when sittinf in 25*c surroundings. use newton's law of cooling to determine how long it will take to cool to 35*c
According to Newton's law of cooling, the rate of cooling is inversely related to the temperature differential between the object and its surroundings. For this, the equation is:
dT/dt = k (T - Ts) (T - Ts)
where T is the object's temperature, Ts is the environment's temperature, and k is the cooling constant. where dT/dt is the rate of change in temperature.
This equation can be used to calculate the cooling constant k for the cup of tea. We know that the temperature started off at 95 degrees Celsius, dropped to 75 degrees Celsius, and took 5 minutes to cool down.
95 - 75 = 20, dT/dt = k (20), dT/dt = k (20) *(1/5), and dT/dt = 4k.
Then, we can determine how long it will take for the temperature to cool to the desired level by using this cooling constant and the target temperature (35°C).
35 - 75 = -40\s-40 = 4k(t) (t)
t = -40 / 4k
We are unable to solve for t since we lack the value for k. But if we assume that the cooling rate is comparable to the rate we currently know, we can come up with an estimate. If we assume that the rate of cooling is constant, we can calculate how long it will take for the tea to cool from 75 to 35 degrees by using the rate of cooling from 95 to 75 degrees.
t = -40/20 equals 2 minutes.
It would take around 2 minutes to cool the tea from 75c to 35c under the assumption of similar cooling rate.
To learn more about newton's law of cooling:
https://brainly.com/question/13748261
#SPJ4
in the following scenarios, the driver of a car has a cup of coffee set in a drink holder. identify how the coffee in the cup would be affected when the car is at constant velocity, speeding up, and slowing down.
The coffee in the cup would be affected differently. At constant velocity, the coffee remains still, when speeding up it is pushed forward, and when slowing down, it is pushed backward.
When the car is at constant velocity, the coffee in the cup would remain still and not spill. However, when the car is speeding up, the coffee in the cup would be pushed forward, and if the car is slowing down, the coffee would be pushed backward.
This is due to the principle of inertia, which states that an object in motion will remain in motion and an object at rest will remain at rest unless acted upon by an unbalanced force.
As the car accelerates or decelerates, the coffee in the cup will experience the force of the car's motion and be pushed in the opposite direction. The amount of force and the resulting movement of the coffee will depend on the acceleration of the car and the size of the cup.
To learn more about inertia visit: https://brainly.com/question/1140505
#SPJ4
We know that the velocity (v(t)) is the derivative of position (x(t)) with respect to time, meaning v(t) = d. Given that, what do we get if we integrate the velocity of an object from t=1 to t=4, meaning Stu(t)dt?
In other words, the integral of the velocity from t=1 to t=4 is the difference between the object's position at t=4 and its position at t=1.
What is velocity?Velocity is a vector quantity that measures the rate of change in an object’s position. It is the rate of displacement (change in position) with respect to time. Velocity is a combination of speed and direction and is typically denoted as v or u in an equation. It is measured in meters per second (m/s) or kilometers per hour (km/h).
The integral of the velocity of an object from t=1 to t=4 is the change in position (x(t)) of the object from t=1 to t=4. This is represented mathematically as:
Stu(t)dt = x(4) - x(1)
In other words, the integral of the velocity from t=1 to t=4 is the difference between the object's position at t=4 and its position at t=1.
To learn more about velocity
https://brainly.com/question/24445340
#SPJ4
which of these four ellipses has the greatest eccentricity? view available hint(s)for part a four ellipses of different elongation are shown. the first ellipse is almost a circle. the second ellipse has the length to width ratio of approximately 2 to 1. the third ellipse has the length-to-width ratio of approximately 1.5 to 1. the fourth ellipse has the length-to-width ratio of approximately 3 to 1. which of these four ellipses has the greatest eccentricity? 2 4 3 1
The fourth ellipse, with the length-to-width ratio of approximately 3 to 1, has the greatest eccentricity.
Eccentricity of the ellipse: The eccentricity of an ellipse is a measure of its "oblateness" or how much it deviates from being a circle. An ellipse has an eccentricity between 0 and 1, with 0 representing a circle and values closer to 1 representing more elongated ellipses. So, in this case, the fourth ellipse with the highest length-to-width ratio would have the highest eccentricity value.
The first ellipse is a circle, it means its length-to-width ratio is 1. Second one is more closer to a circle than the third one. Similarly third ellipse is more closer to the circle than the fourth one.
To know more about ellipse, here
https://brainly.com/question/14281133
#SPJ4
A 65.2 kg base runner begins his slide into second base while moving at a speed of 4.93 m/s. He slides so that his speed is zero just as he reaches the base. The acceleration of gravity is 9.8 m/s². What is the magnitude of the mechanical energy lost due to friction acting on the run- ner? Answer in units of J.
Answer:
about 792 J
Explanation:
You want the mechanical energy lost by a 65.2 kg base runner who slides into second base from a speed of 4.93 m/s, reaching the base with a speed of 0.
Kinetic energyThe runner's kinetic energy is ...
KE = 1/2mv²
KE = 1/2(65.2 kg)(4.93 m/s)² = 792.33974 J
As the runner slides into second base, his speed decreases to zero, so all of his kinetic energy is lost to friction.
The energy lost to friction is about 792 J.
how can a simple fixed pulley make a job easier
a. by decreasing the work done
b. by changing the direction at which the force needs to be applied
c. by decreasing the distance that the force needs to be applied
d. by decreasing the force required to lift the object
It is considerably easier for us to move objects thanks to simple machinery called pulleys that can shift the direction of force. The amount of force necessary to lift something up is reduced by this procedure. Option d
What does a scientific force mean?A clear meaning is attached to the word "force." The terms "push" and "pull" are perfectly acceptable at this level to describe forces. An object does not have a force inside of it or within it.
Who or what is force?A massed item changes its velocity in response to a push or pull. A body can change its state of rest or motion when an external force acts on it. It is directed and has a magnitude.
To know more about Force visit:
https://brainly.com/question/13191643
#SPJ1
A uniform electric field exists everywhere in the x, y plane. This electric field has a magnitude of 4500 N/C and is directed in the positive x direction. A point charge -8.0 x 10-9 C is placed at the origin. �Determine the magnitude of the net electric field at (a) x = -0.15 m, (b) x = +0.15 m, and (c) y = +0.15 m.
The magnitude of the net electric field
At x = - 0.15 m is 7,700 N/C and is directed in the positive x direction.At x = 0.15 m is 1,300 N/C and is directed in the positive x direction.At y = 0.15 m is 5,521.78 N/C and is directed in 324.58° from the positive x direction.The direction of the net electric field from a point to a negative charge is from the point to the charge. The magnitude of the electric field from the point to a point charge
E = kq ÷ r²
k = an electrostatic constant = 9 × 10⁹ Nm²/C² q = point charge = - 8.0 × 10⁻⁹ C r = Distant between point and point charge (m)E = The magnitude of electric fields (N/C) Electric fields in the systemE₂ is the electric fields from a point charge to r = 0.15 m
E₂ = 9 × 10⁹ × 8.0 × 10⁻⁹ ÷ 0.15²
E₂ = 72.0 ÷ 0.0225
E₂ = 3,200 N/C
a. At x = - 0.15 m
Look at picture a
The direction E₂ from x = - 0.15 to the origin.b. At x = 0.15 m
Look at picture b
The direction E₂ from x = 0.15 to the origin.c. At y = 0.15 m
Look at picture c
The direction E₂ from y = 0.15 to the origin.Learn more about electric field here: https://brainly.com/question/28027633
#SPJ4
what is the direction of the acceleration of the object at moment 5? enter the letter of the arrow with this direction from the compass rose in the figure. type z if the acceleration vector has zero length.
The direction of the acceleration of the pendulum at moment 5 is towards A (center), which is perpendicular to the direction of motion of the bob.
There is no any component of force acting along the tangent direction, when the bob is at the equilibrium mid-position as the string is completely vertical. Restoring force is momentarily absent in the bob when it is moving through the equilibrium position. The restoring force is only required when the pendulum bob has been slightly displaced away from the equilibrium position.
In the equilibrium position, the tension force is greater than the perpendicular component of gravity when the bob moves through this equilibrium position. As the bob continues its motion along a circular arc, so there must be a net centripetal force towards the center. So the direction will be towards A.
--The given question is incomplete, the complete question is:
"what is the direction of the acceleration of the object at moment 5? enter the letter of the arrow with this direction from the compass rose in the figure. type z if the acceleration vector has zero length."
To know more about pendulum, here
https://brainly.com/question/14759840
#SPJ4
a 64.0-kg bungee jumper steps off a bridge with a light bungee cord tied to her and to the bridge. the unstretched length of the cord is 15.0 m. the jumper reaches reaches the bottom of her motion 41.0 m below the bridge before bouncing back. we wish to find the time interval between her leaving the bridge and her arriving at the bottom of her motion. her overall motion can be separated into an 15.0-m free-fall and a 26.0-m section of simple harmonic oscillation.
The free-fall and oscillation sections, which is [tex]$3.02 \ s + 2.01 \ s = 5.03 \ s$[/tex].
What is oscillation sections?Oscillation sections are sections of a waveform that repeat themselves over a certain period of time. This period of time is known as the oscillation period and is typically measured in seconds or milliseconds.
The time interval between the bungee jumper leaving the bridge and reaching the bottom of her motion can be found by summing the time intervals associated with the free-fall and oscillation sections of the motion.
The time interval associated with the 15.0 m free-fall can be found using the equation for the time it takes an object to fall a given distance, which is:
[tex]$t_{fall} = \sqrt{\frac{2d}{g}}$[/tex]
where d is the distance fallen and g is the acceleration due to gravity, which is [tex]9.81 m/s$^2$.[/tex]
Therefore, the time interval associated with the free-fall can be calculated as follows:
[tex]$t_{fall} = \sqrt{\frac{2 \cdot 15.0 \ m}{9.81 \ m/s^2}} = 3.02 \ s$[/tex]
The time interval associated with the 26.0 m of oscillation can be found using the equation for the period of a simple harmonic oscillator, which is:
[tex]$T = 2 \pi \sqrt{\frac{m}{k}}$[/tex]
where $m$ is the mass of the object and k is the spring constant.
In this case, the mass of the object is 64.0 kg, and the spring constant is the force of gravity acting on the jumper, which is [tex]$mg = 64.0 \ kg \cdot 9.81 \ m/s^2 = 628.64 \ N/m$[/tex]
Therefore, the time interval associated with the oscillation can be calculated as follows:
[tex]$T = 2 \pi \sqrt{\frac{64.0 \ kg}{628.64 \ N/m}} = 2.01 \ s$[/tex]
The total time interval between the bungee jumper leaving the bridge and reaching the bottom of her motion is the sum of the time intervals for the free-fall and oscillation sections, which is [tex]$3.02 \ s + 2.01 \ s = 5.03 \ s$[/tex].
To learn more about harmonic oscillator
https://brainly.com/question/26114128
#SPJ4
in fig. 22-51, two curved plastic rods, one of charge q and the other of charge iq, form a circle of radius r i 8.50 cm in an xy plane. the x axis passes through both of the connecting points, and the charge is distributed uniformly on both rods. if q i 15.0 pc, what are the (a) magnitude and (b) direction (relative to the positive direction of the x axis) of the electric field e produced at p, the center of the circle?
The answer is 23.8 N/C.
From symmetry, we see that the net field at
P is twice the field caused by the upper semicircular charge
+q=λ(πR)
What is electric field?The physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, either attracting or repelling them, is known as an electric field (also known as an E-field[1]). [2] It can also refer to a system of charged particles' physical field. [3] Electric charges and time-varying electric currents are the building blocks of electric fields. The electromagnetic field, one of the four fundamental interactions (also known as forces) of nature, manifests itself in both electric and magnetic fields.
Electrical technology makes use of electric fields, which are significant in many branches of physics. For instance, in atomic physics and chemistry, the electric field acts as an attracting force to hold atoms' atomic nuclei and electrons together. Additionally, it is the force that causes atoms to connect chemically.
Learn more about electric field here: https://brainly.com/question/19878202
#SPJ4
How are atoms molecules, compounds, and pure substances
related?
Elements are most simply made up of atoms. A pure element will only have one type of atom, for example, a pure chunk of gold will only have gold atoms, making it chemically pure.
Two identical atoms bonded chemically, most frequently by covalent bonds, to form a molecule. Halogens are typically diatomic molecules; for example, chlorine is known as Cl2.
A pure substance is made up of various elements that have been chemically combined. Ionic chemicals that are connected by ionic bonds are the most common way to observe this. Please remember that a compound is not the same as a mixture! Keep in mind that a combination is not linked chemically.
to know more about molecules, compounds and pure substances, see
https://brainly.com/question/475709
https://brainly.com/question/26487468
https://brainly.com/question/18634105
the charge on a nonconducting rod increases linearly from end a to end b. the rod is bent in a circle so that ends a and b almost meet very near the top of the circle (figure 1). figure1 of 1 a positively charged rod a b is bent into a ring so that its ends almost meet at the top of the ring. end b is on the left, end a is on the right. the center of the ring is marked by a black dot. a dashed horizontal line passes through the black dot. part a what is the direction of the electric field at the center of the circle? (hint: consider contributions from diametrically opposite segments!)
A uniformly charged ring has zero electric field at its center. Radially inwards toward negative point charge and outwards from positive charge is the electric field.
Which way does the electric field point in the center of a charged circular loop?Radially inwards toward negative point charge and outwards from positive charge is the electric field.A uniformly charged ring has zero electric field at its center.Both of the electric fields that are donated to the dipole are pointing in the same general direction—that is, toward the negative charge—in the middle of the dipole.The electric field's strength can be calculated using the equation E = k | Q | r 2 by using the formula. The charge's sign—negative in this instance—determines the direction of the electric field.To learn more about electric field refer to:
https://brainly.com/question/14372859
#SPJ4
a person wants to transmit an audio file from a device to a second device. which of the following scenarios best demonstrates the use of lossless compression of the original file? What is the speed of the block immediately after the bullet exits?
The answer is that A device compresses the audio file before transmitting it to a second device. The second device restores the compressed file to its original version.
What is an compresses an audio file?To compresses an audio file is a term that connote the act of making an audio file to be smaller in size so as to fit into a given device or app. Note that the option that best demonstrates the use of lossless compression of the original file is that A device compresses the audio file before transmitting it to a second device. The second device restores the compressed file to its original version before playing it and as such, option A is correct.
Here,
The solution is that before sending the audio file to a second device, A compresses it. The second device converts the compressed file back to its original state.
Learn more about audio file,
brainly.com/question/2561725
#SPJ4
if your hot pot has a power rating of 600 watts, show how to find how long it will take to complete the process. (make sure you are comfortable using standard units of energy, and that you understand the relation of power to energy. hint: what are watts?)
It will take 91.125 sec (approximately 1 min and 30 sec) to complete the process using a hot pot with a power rating of 600 watts.
How does the conversion process of ice to water occur?The process of converting 150 pieces of ice at -15 degrees Celsius into liquid water at 50 degrees Celsius is an endothermic process, meaning that heat is absorbed by the system. To represent this process in an energy-interaction diagram, we would start with the initial state of the ice at -15 degrees Celsius, with the horizontal axis representing the amount of energy absorbed by the system (in joules) and the vertical axis representing the temperature. As heat is added to the system, the temperature of the ice will increase, and the energy absorbed by the system will also increase. The process will continue until the ice has completely melted and reached a temperature of 50 degrees Celsius, at which point the energy absorbed by the system will reach its maximum value.
The amount of heat added to the system to complete this process can be calculated using the formula:
Q = mcΔT
where Q is the heat added (in joules), m is the mass of the ice (in kilograms), c is the specific heat capacity of ice (about 2.1 J/gC), and ΔT is the change in temperature (50 - (-15) = 65 degrees Celsius). The heat absorbed by the system is therefore calculated as follows:
Q = 150 pieces × 0.02 (kg/piece) × 2.1 (J/g*C) × 65(C) = 54675 J
It will take 91.125 sec (approximately 1 min and 30 sec) to complete the process using a hot pot with a power rating of 600 watts.
How does the conversion process of ice to water occur?The process of converting 150 pieces of ice at -15 degrees Celsius into liquid water at 50 degrees Celsius is an endothermic process, meaning that heat is absorbed by the system. To represent this process in an energy-interaction diagram, we would start with the initial state of the ice at -15 degrees Celsius, with the horizontal axis representing the amount of energy absorbed by the system (in joules) and the vertical axis representing the temperature. As heat is added to the system, the temperature of the ice will increase, and the energy absorbed by the system will also increase. The process will continue until the ice has completely melted and reached a temperature of 50 degrees Celsius, at which point the energy absorbed by the system will reach its maximum value.
The amount of heat added to the system to complete this process can be calculated using the formula:
Q = mcΔT
where Q is the heat added (in joules), m is the mass of the ice (in kilograms), c is the specific heat capacity of ice (about 2.1 J/gC), and ΔT is the change in temperature (50 - (-15) = 65 degrees Celsius). The heat absorbed by the system is therefore calculated as follows:
Q = 150 pieces × 0.02 (kg/piece) × 2.1 (J/g*C) × 65(C) = 54675 J
To find out how long it will take to complete the process using a hot pot with a power rating of 600 watts, you can use the formula:
time (in seconds) = energy (in joules) / power (in watts)
time = 54675 J / 600 W = 91.125 sec (approximately 1 min and 30 sec)
To know more about endothermic process, visit:
https://brainly.com/question/29555731
#SPJ4
in an electric circuit, a single wire is connected to three branches that contain resistors. the three branches then connect back to a single wire. the current in each of the single wires is the same. conservation of which of the following best explains this phenomenon?
The current in each of the single wires being the same in an electric circuit with a single wire connected to three branches that contain resistors and then connecting back to a single wire is explained by the conservation of charge.
What is conservation of charge?Conservation of charge states that total charge in an isolated system remains constant. In electric circuit, charge flows through circuit in the form of electric current. Therefore, amount of charge flowing into any point in the circuit must be equal to the amount of charge flowing out of that point.
This means that current flowing into a branch in the circuit must be equal to the current flowing out of that branch. As the current in the single wire connected to the three branches is the same, current flowing into and out of each branch must also be the same, as per the conservation of charge principle.
To know more about electric circuit, refer
https://brainly.com/question/2969220
#SPJ4
Explain the sources of instrumental errors
Answer:
A pH meter that reads 0.5 off or a calculator that rounds incorrectly would be the source of instrumental errors.
A 500 kg roller coaster car starts from rest at point A and moves down the curved track._ The speed of the car at the point C is 10 m/s. Calculate the energy loss due to friction from A to C
The appropriate values into the equation: E = (500 kg) (9.81 m/s2) (change in height between A and C).
What is equation?An equation is a mathematical statement that expresses the relationship between two or more variables. It is composed of algebraic expressions, including constants, coefficients, variables, and operators, arranged in a particular order.
The energy loss due to friction from A to C can be calculated using the equation E = mgh, where m is the mass of the car (500 kg), g is the acceleration due to gravity (9.81 m/s2), and h is the change in height between points A and C.
Assuming that the track is level between A and C,
then the change in height is zero and the energy loss due to friction is also zero. If, however,
the track is not level and there is a change in height between A and C,
then the energy loss due to friction can be calculated by plugging in the appropriate values into the equation: E = (500 kg) (9.81 m/s2) (change in height between A and C).
To learn more about equation
https://brainly.com/question/26408808
#SPJ4
the built-up shaft consists of a pipe ab and solid rod bc. the pipe has an inner diameter of 20 mm and outer diameter of 28 mm. the rod has a diameter of 12 mm. determine the average normal stress at points d and e and represent the stress on a volume element located at each of these points.
In order to determine the average normal stress at points D and E, we need to know the applied loading and the cross-sectional areas of the pipe and rod at these points.
It is assumed that pipe AB and solid rod BC form a built-up shaft that is subjected to an axial load, represented by P. The average normal stress at point D, which is located on the pipe, can be calculated by:
σD = P/A
Where A is the cross-sectional area of the pipe at point D. The cross-sectional area of the pipe can be calculated by:
A = π/4 * (D_o^2 - D_i^2)
Where D_o is the outer diameter of the pipe and D_i is the inner diameter of the pipe
The average normal stress at point E, which is located on the rod, can be calculated by:
σE = P/A
Where A is the cross-sectional area of the rod at point E. The cross-sectional area of the rod can be calculated by:
A = π/4 * D_r^2
Where D_r is the diameter of the rod
Therefore, by substituting the given values into the above equations we can calculate the average normal stress at points D and E.
Learn more about Stress here: https://brainly.com/question/29488474
#SPJ4
instructor problem 2: the mega 2560 has a built in 10 bit a/d, typically mapped with the input range 0-5 volt. sketch a curve similar to the curve below that relates input voltage (bottom axis) to output bits (vertical axis). show quantization levels etc.. you may want to search the internet for some ideas.
The Mega 2560 has a 10-bit A/D converter built-in. This means that analog input voltages can be converted to digital values with a resolution of 10 bits. Typically, a range of 0 to 5 volts is used to map the input voltage range.
With input voltage on the lower axis and output bit on the vertical axis, a graph representing the relationship between the two variables can be created. The A/D converter's quantization levels are represented by the curve. These discrete steps are used to turn the input voltage into a digital value.
The quantization levels within the input voltage range of a 10-bit A/D converter are evenly distributed. The minimum input voltage is equivalent to a digital value of 0, and the maximum input voltage is equivalent to a digital value of 1023. Each quantization level has a corresponding digital value.
To learn more about the input voltage and output bits at
https://brainly.com/question/13185360?referrer=searchResults
#SPJ4
The question is -
The mega 2560 has a built-in 10-bit a/d, typically mapped with the input range of 0-5 volts. sketch a curve similar to the curve below that relates input voltage (bottom axis) to output bits (vertical axis). show quantization levels. So connect your LED and your 220 W resistor to pin 9 and ground. In your code you can get rid of the serial monitor code, and define what pin the LED is connected to int ledPin = 9; under setup add pinMode(ledPin, OUTPUT); Next, define a new integer variable called val and set it equal to the value of the sense in (use analogRead(sensePin)).
A beachgoer in Florida notices the waves crashing ashore are spaced 13 meters apart and hit the shore every 6 s. How fast (in m/s) are the waves traveling?
The speed of the waves at the beach in Florida is 2.167 m.s.
What is the wavelength of the wave?The wavelength of a wave is the distance between successive points in a wave.
The wavelength of the given wave is obtained as follows:
Wavelenegh of the wave = 13 meters
The frequency of the wave is 1/6 per second
The wavelength, speed, and frequency of the wave is related as follows;
The velocity of a wave = wavelength * frequency
The speed or velocity of the wave = 13 * 1/6
The speed or velocity of the wave = 2.176 m/s
Learn more about wavelength and speed of a wave at: https://brainly.com/question/3148541
#SPJ1
figure 22-53 shows two concentric rings, of radii r and r 3.00r, that lie on the same plane. point p lies on the central z axis, at distance d 2.00r from the center of the rings. the smaller ring has uniformly distributed charge q. in terms of q, what is the uni- formly distributed charge on the larger ring if the
Symmetry: According to the problem the charge on the larger ring is 4q.
What is Symmetry?Symmetry is a type of balanced arrangement of parts or elements of a whole. It is a fundamental concept in mathematics, art, and nature. Symmetry can be seen in everyday objects, such as a human face, a butterfly, a snowflake, and a fingerprint.
This is because of the symmetry of the system. The electric field due to the smaller ring at point P is the same as the electric field due to the larger ring at point P, since the distance from point P to the center of both rings is the same. Since the charge on the smaller ring is q, the charge on the larger ring must also be q in order to produce the same electric field. Since the larger ring has four times the area of the smaller ring, the charge on the larger ring must also be four times that of the smaller ring, which is 4q.
To learn more about Symmetry
https://brainly.com/question/26275735
#SPJ4
the 50-kg passenger in a car moving at 10 m/s crashes into a tree and stops in 0.2 seconds. the average force exerted on the passenger to bring her to a stop is
The passenger experiences a 2500 Newton force on average to stop the vehicle.
We may use the formula force = mass x acceleration to get the average force applied on the passenger. The passenger's deceleration in this scenario is the acceleration, which can be computed by dividing the velocity change by the time change.
The passenger's velocity in this instance decreases from 10 m/s to 0 m/s in 0.2 seconds, hence the deceleration is as follows:
deceleration = (change in velocity) / (change in time)
Substitute the value in above equation we get,
deceleration = (0 m/s - 10 m/s) / 0.2 seconds
deceleration = -50 m/s²
Remember that the acceleration is moving in the opposite direction of the velocity when the sign is negative. In this instance, the passenger is originally travelling forward at a positive velocity, but the deceleration is negative, demonstrating that the force is pushing on the passenger from the opposite direction and slowing her down.
Thus, the passenger is subjected to the following force:
mass times acceleration equals force.
Substitute the value in above equation we get,
force = 50 x -50 = 2500 N.
force = 2500 Newton
For such more question on average force
https://brainly.com/question/18652903
#SPJ4
Occurs when the type, degree, and duration of force employed was not necessary or appropriate.
The type, degree, and duration of force that is employed during the moment was not necessary.
in mechanics, any action that seeks to preserve, modify, or deform a body's motion. Isaac Newton's three laws of motion, which are outlined in his Principia Mathematica, are frequently used to illustrate the concept of force (1687).
Simple people with simple minds teach simple subjects, like physics. The first thing physicists do when they examine an object is to simplify it. A book is a box, not a collection of paper sheets attached with glue and string. A automobile is a box; it doesn't have rotating rubber tires, six-way adjustable seats, lots of cup holders, or a rear window defogger. A human is not formed of bone, muscle, skin, and hair; rather, they are a box with two arms, two legs, and a head. This is the start of a free body diagram, a style of drawing popular among engineers and physicists.
The foundation of physics is the logical process of analysis, which involves dissecting complex circumstances into a collection of smaller ones.
Learn more about force
brainly.com/question/13191643
#SPJ4
What fraction of its initial kinetic energy is lost?
Express your answer using two significant figures.
K lost/ K initial=?
The fraction of its initial kinetic energy lost can be estimated to be 0.10 to 0.20.
What is initial kinetic energy?Initial kinetic energy is the energy possessed by an object due to its motion. It is the energy of an object before any other external forces, such as gravity, friction, or air resistance, act upon it. Kinetic energy is a scalar quantity, meaning it has magnitude but not direction.
The fraction of kinetic energy lost will depend on the nature of the collision and the amount of energy dissipated. Generally, it is estimated that about 10% to 20% of the initial kinetic energy is lost in a collision. Therefore, the fraction of its initial kinetic energy lost can be estimated to be 0.10 to 0.20.
To learn more about initial kinetic energy
https://brainly.com/question/13026615
#SPJ4
water flows with speed v through a horizontal, cylindrical pipe. which of the following changes in the geometry of the pipe will double the speed of the water in the pipe?
Halving the area of the pipe will double the speed of the water in the pipe. Therefore, option(c) is the correct answer.
Given,
initial flow speed, V₁ = v
let's area, A₁ = A
Now, to double the speed of the water flow
V₂ = 2v
we know that,
using continuity equation of flow:
A₁V₁ = A₂V₂
or A x v = A₂ x 2v
A₂ = A/2 or A₁/2
Therefore, By Halving the area of the pipe will double the speed of the water in the pipe.
To learn more about the continuity equation:
https://brainly.com/question/30267328
#SPJ4
The complete question is:
water flows with speed v through a horizontal, cylindrical pipe. which of the following changes in the geometry of the pipe will double the speed of the water in the pipe?
(a) Doubling the area of the pipe
(b) Doubling the radius of the pipe
(c) Halving the area of the pipe
(d) Halving the radius of the pipe
let v be the center of mass of a system of point masses located at v1, . . . , vk in r 3 . is v in span{v1, . . . , vk}? explain.
No, v is not in span{v1, . . . , vk}, because the center of mass of a system of point masses is a vector that lies outside of the span of any of the individual point masses.
What is vector?A vector is a mathematical object used in computer programming and other fields. It is a collection of elements, usually numbers or other data points, represented by a single line segment and denoted by an arrow. Vector elements are often used to represent physical quantities such as velocity, acceleration, force, or position. In computer programming, vectors are used to store data in a structured way.
The center of mass is calculated by taking the weighted average of the positions of the individual point masses, thus it is a vector that lies in between the points of the system rather than being one of the points itself.
To learn more about vector
https://brainly.com/question/356987
#SPJ4
the rigid bar efg is supported by the truss system shown. knowing that the member cg is a solid circular rod of 0.75-in. diameter, determine teh normal stress in cg
Normal stress in CG is 13.58 Ksi
When the deforming force is applied to an item, it deforms. The object will generate an opposing force from within to revert to its previous dimensions and shape. This restoring force will be applied in the opposite direction and have the same magnitude as the deforming force.Stress is a term used to describe how much of this restorative force is produced per unit area of the material. When the path of the deforming force is perpendicular to the body's cross-sectional area, stress is said to be normal stress. If the wire's length or the body's volume changes, the stress level will remain normal.
Using the portion EFCGB as a free body ,
∑[tex]F_{y} =0 :[/tex]
[tex]\frac{3}{5}F_{AE}[/tex]-3600=0
[tex]F_{AE}[/tex]=6000 lb
Using beam EFG as a free body ,
+[tex]M_{F} =[/tex]0 ,
-(4) [tex]\frac{3}{5}F_{AE}[/tex] + (4)[tex]\frac{3}{5}F_{cc}[/tex] = 0
[tex]F_{cc} =F_{AE} =[/tex]6000lb
cross section area of member CG :
[tex]A_{CG}=\frac{\pi}{4} d^{2}[/tex]= [tex]\frac{\pi}{4} (0.75)^{2}[/tex]
[tex]A_{CG}=0.44179 \:in^{2}[/tex]
Let the normal stress is 'B'
Normal stress in CG
[tex]B_{CG} =\frac{ F_{CG} }{ A_{CG} }[/tex] = [tex]\frac{6000 }{0.44179 }[/tex] = 13,580 psi
[tex]B_{CG} =[/tex] 13.58 Ksi
Learn more about normal stress
brainly.com/question/28012990
#SPJ4
If 240 million people in the United States jumped up into the air simultaneously pushing off the earth with an average force of 800 N each for 0.10 s, what would happen to the 5.98x10^24 kg earth?
when 270 million people jump at the same time the Earth will move at 1.3 m/s.
What is average force?The vector quantity of a force. It is a quantity with both magnitude and direction, hence.
We must specify both the size and the direction of the force operating on an object in order to adequately understand it. The average force is the force applied by an item traveling over a specific period of time at a defined rate of speed, or velocity.
This velocity is not instantaneous or precisely calculated, as the word "average" indicates. As a result, the average force is determined by multiplying the body's mass by the object's average velocity during the specified period of time.
Therefore, when 270 million people jump at the same time the Earth will move at 1.3 m/s.
To learn more about average force, refer to the link:
https://brainly.com/question/29781083
#SPJ1
charges on raindrops vary widely in both magnitude and sign. consider a case where the two drops on the x -axis are 2.18 mm apart and have charge q=-1.87miuC. Find the electric force on the upper drop.
The electrostatic force acting on the charge is Fe = 1.5 × 10^-3N The magn
Find the electric force on the upper drop?
We can use the equation E = k | Q | r 2 E = k | Q | r 2 to find the magnitude of the electric field. The direction of the electric field is determined by the sign of the charge, which is negative in this case. E = k | Q | r 2 = ( 8.99 × 10 9 N ⋅ m 2 /C 2 ) | − 1.5 × 10 − 9 C | ( 0.035 m ) 2 = 1.1 × 10 4 N/C.The repulsive or attractive interaction between any two charged bodies is called as electric force. Similar to any force, its impact and effects on the given body are described by Newton's laws of motion. The electric force is one of the various forces that act on objects.Coulomb's law calculates the magnitude of the force F between two point charges, q1 and q2, separated by a distance r. F=k|q1q2|r2.To learn more about electric force refers to:
https://brainly.com/question/21980164
#SPJ4
Which of the following practices are common ways in which journalists misrepresent research studies in their media articles?
Journalists frequently misinterpret research studies in their media articles in a number of ways. Such practices can lead to inaccurate and potentially harmful messages about scientific research.
Misinterpretation of research studies occurs in several ways:
First, journalists may inaccurately represent the findings of a study, either by overstating its conclusion or by misinterpreting its results. For example, they may suggest that a study shows a causative relationship between two variables when the actual findings only show a correlation.
Second, journalists may fail to provide enough context for readers to understand the research. This includes not providing enough information about the study sample and design, as well as failing to explain the statistical methods used in the analysis.
Third, journalists may selectively report on research studies, emphasizing those that are most sensational or that support a particular narrative. By omitting certain study results, they may give an incomplete picture of the research at hand.
Finally, journalists may report on studies that contain weak or unreliable evidence. This is particularly problematic when the research is based on a small sample size or uses methods that are not well-validated.
In summary, journalists are prone to misrepresenting research studies by giving an incomplete account of the findings, failing to provide adequate context, selectively reporting on studies, and relying on unreliable evidence. Such practices can lead to inaccurate and potentially harmful messages about scientific research.
Learn more about research studies:
https://brainly.com/question/9266703
#SPJ4