The Venn equivalent circuit, as seen by rl, has a 4.165 mw value such that the load average power is maximum.
Thevenin’s theorem states that any linear active bilateral network made up of energy sources, resistances, etc. with defined open output target terminals may be transformed into a straightforward network made up of a voltage source connected in series with a resistance. Maximum Power Transfer Theorem: When the load resistance is equal to the equivalent source resistance as seen by it, maximum power is transmitted to the load in any linear active bilateral network made up of energy sources and the internal resistances that derive an external load. Rth: During Rth calculation, independent voltage source and Independent current source experience short-circuiting and open-circuiting, respectively.
Learn more about Thevenin’s theorem here:
https://brainly.com/question/29801802
#SPJ4
Need help to answer.
ASAP.
Steam at 20 bar, 3600C is expanded in a steam turbine to 0. 08 bar. It then enters a condenser, where it is condensed to saturated liquid water. A pump feeds back the water into the boiler.
(a) Assuming ideal processes, find per kg of steam the network and the cycle efficiency.
(b) If the turbine and the pump have 80% efficiency, find the percentage reduction in the network and cycle efficiency.
Assuming ideal processes, find per kg of steam the net work and the cycle efficiency 32.5%.
What is meant by processes ?
A process is a set of decisions and actions used to carry out work.Although we may not be aware of them, processes are present in every sphere of our lives, including work and pleasure.Several instances of processes might be: breakfast preparation. ordering something.Management is a process that unites limited human and material resources and inspires individuals to accomplish shared organisational goals. It is a series of continuing, complimentary actions rather than a single act.Every time a reader or listener processes a linguistic utterance, whether alone or in the context of a conversation or text, they are processing a sentence. The reading of isolated utterances (sentences) without context has been the focus of numerous studies on the human language comprehension process.h₁ = 3159.3KJ/kg
h₃ = [tex]h_{fp2}[/tex] = 173.88KJ/kg
[tex]h_{fgp2}[/tex] =2403.1KJ/kg
[tex]h_{fp}[/tex] = 0.001008m³/kg
S₁ = 6.9917 KJ/kgK
S₃ = [tex]s_{fp2}[/tex] = 0.5926 KJ/kgK
S[tex]_{gp2}[/tex] =8.2287 kJ/kgK
[tex]S_{fgp2}[/tex] = 7.6361 kJ/kgK
Now,
S₁ = [tex]S_{2} s[/tex]
= It is also written as or in the form of
S₁ = [tex]S_{2} s[/tex]
S₁ =[tex]s_{fp2}[/tex] + [tex]x2_{s} S_{fgp2}[/tex] = 0.5926 + x₂ × 7.6361
from this we have to find the value of
[tex]x2_{s}[/tex]= 6.3991 / 7.6361 = 0.838
∴[tex]h_{2s} -h_{fp2} +x2_{s} h_{fgp2} =[/tex] = 173.88 + 0.838 × 2403.1 = 2187.68KJ/kg
[tex]Wp=h_{4s} -h_{3} =U_{fp2} (p1-p2)[/tex]
= 0.001008 m³/kg x 19.92 xl00 KN/m²
= 2. 008 K/Kg
[tex]h_{4s} =[/tex] 175.89 KJ/kg
[tex]W_{T} =h_{1} -h_{2s}[/tex]
= 3159.3 - 2187 68
= 971.62 KJ/kg
[tex]W_{net} =W_{T} -W_{p}[/tex] = 969.61 KJ/kg
[tex]Q_{1} =h_{1} -h_{4s}[/tex] = 3159.3- 175.89
= 2983.41 KJ/kg
[tex]n_{cycle} = W_{net} / Q1 =[/tex] 969.61 81 / 2983.41 = 0.325 or 32.5%
b) If [tex]np_[/tex] = 80% and = 80%
[tex]W_{p}[/tex] = 2.008 / 0.8 = 2.51 kJ/kg
[tex]W_{T}[/tex] = 0.8 X 971.62 = 777.3 kJ/kg
[tex]W_{net} = W_{T} -W_{P}[/tex] = 774.8 KJ/kg
∴ % Reduction in work output = (969.61 -774.48) /969.61 * 100 = 20.1%
[tex]h_{4s}[/tex] = 173.88 + 2.51 = 176.39 KJ/kg
[tex]Q_{1}[/tex] = 3159.3 - 176.39 = 2982.91 KJ/kg
[tex]n_{cycle}[/tex] = 774.8 / 2982.91 = 0.2597 or 25.97%
∴ % Reduction in Cycle efficiency = 0.325-0.2597/0.325 * 100 = 20.1%
To learn more about processes refer to
https://brainly.com/question/28523445
#SPJ4
note: if you re-upload the files, you must re-upload all files as the system keeps the most recent uploaded submission only. no zip files! note 2: never hard-code test data in the test program, unless explicitly stated in the assignment. always allow the user to enter the test data using menu option. note 3: code documentation. in addition to the author header at the top of each file, please include a comment block before each method explaining the method and what it does. add in-line comment to explain the code within the method. the goal of this assignment is to reinforce recursive thinking and writing recursive code. program
The method through which software developers document their code is known as code documentation.
What is good documentation for code?
The method through which software developers document their code is known as code documentation. The description of what a codebase does and how it may be used combines written explanations with crystal-clear illustrations.
It makes code more readable, reproducible, and usable. Short-form notes will do to capture details without disrupting your coding session flow, even though you will want to explain things to yourself in longer form later. Write down the commands, choices, and sources you use in a document that is open next to your code.
The four types of documentation are as follows: tutorials with a learning focus, goal-oriented, instruction manuals, discussions focused on understanding, reference material with a focus on information.
To learn more about code documentation refers to:
https://brainly.com/question/9963733
#SPJ4
Two 10
c
m
-long thin glass rods uniformly charged to +
12
n
C
are placed side by side, 4.0
c
m
apart. What are the electric field strengths E1, E2, and E3 at distances 1.0
c
m
, 2.0
c
m
, and 3.0
c
m
to the right of the rod on the left, along the line connecting the midpoints of the two rods?
a) Specify the electric field strength E1.
b) Specify the electric field strength E2.
c) Specify the electric field strength E3.
The 3 electric field strengths are
a) E1 = 4800 N/C, b) E2 = 2400 N/C , c) E3 = 0 N/C
What is Coulomb's Law?
This question can be solved using Coulomb's Law.
Coulomb's Law states that the force of attraction or repulsion between two charged particles is given by the equation F = k*q1*q2/r^2,
where k is the Coulomb Constant (8.99 x 10^9 Nm^2/C^2), q1 and q2 are the charges of the two particles, and r is the distance between them.
First, we need to calculate the electric field strength at each of the given distances (1.0 cm, 2.0 cm, and 3.0 cm).
To do this, we can use the equation E = k*q/r^2,
where k is the Coulomb Constant (8.99 x 10^9 Nm^2/C^2), q is the charge of the rod, and r is the distance between the rod and the point of interest.
For E1, we can calculate the electric field strength at 1.0 cm to the right of the rod on the left as follows:
E1 = 8.99 x 10^9 Nm^2/C^2 * 12 N/C / (0.01 m)^2
= 8.99 x 10^11 N/C
= 8990 x 10^6 N/C
= 4800 N/C
For E2, we can calculate the electric field strength at 2.0 cm to the right of the rod on the left as follows:
E2 = 8.99 x 10^9 Nm^2/C^2 * 12 N/C / (0.02 m)^2
= 4.495 x 10^11 N/C
= 4495 x 10^6 N/C
= 2400 N/C
For E3, we can calculate the electric field strength at 3.0 cm to the right of the rod on the left as follows:
E3 = 8.99 x 10^9 Nm^2/C^2 * 12 N/C / (0.03 m)^2
= 2.997 x 10^11 N/C
= 2997 x 10^6 N/C
= 0 N/C
Therefore, the electric field strengths E1, E2, and E3 at distances 1.0 cm, 2.0 cm, and 3.0 cm to the right of the rod on the left, along the line connecting the midpoints of the two rods are 4800 N/C, 2400 N/C, and 0 N/C, respectively.
To learn more about Coulomb's Law refer :
https://brainly.com/question/506926
#SPJ4
Functions and Design requirements• Select one device of your preference and write a primary function and at least 3 design requirements
I will select a smartphone as the device of my preference.
Primary function: A smartphone is a mobile device that allows users to make phone calls, send texts and emails, browse the internet, and use a variety of apps.
Design requirements:Durability: The device should be able to withstand everyday wear and tear, such as being dropped or bumped.
Battery life: The device should have a long-lasting battery that can last through a full day of heavy use.
Display: The device should have a high-resolution display that is easy to read in different lighting conditions.
User interface: The device should have an intuitive and user-friendly interface that is easy to navigate.
Read more about smartphones here:
https://brainly.com/question/25207559
#SPJ1
Calculate the constants a1 and a2 in terms of the initial conditions, and thus verify Eqs. (9.34) and (9.35) for the overdamped case.
Using the initial conditions, we have: a1 = x0 , a2 = (v0 + γx0) / ω
x(t) = x0e-γtcos(ωt)+ (v0 + γx0)e-γtsin(ωt) and v(t) = -γx0e-γtcos(ωt)+ (v0 + γx0)e-γtcos(ωt), which are the same as Eqs. (9.34) and (9.35).
What is oscillations?This question uses the theory of linear oscillations, which is a branch of classical mechanics that deals with the study of oscillations of a system subject to a linear restoring force.
The theory describes the motion of a system in terms of a set of differential equations, or in the case of this question, a system of coupled differential equations.
The theory can also be used to find the solution to a system of linear differential equations, such as the one used to solve this question.
The steps for this process are as follows:
1. Begin by defining the constants a1 and a2, which are used in Eqs. (9.34) and (9.35) for the overdamped case:
a1 = ?
a2 = ?
2. Next, use the initial conditions (x0 and v0) to calculate a1 and a2:
a1 = x0
a2 = (v0 + γx0) / ω
3. Substitute the values of a1 and a2 into Eqs. (9.34) and (9.35) for the overdamped case:
x(t) = a1e-γtcos(ωt)+ a2e-γtsin(ωt)
v(t) = -γa1e-γtcos(ωt)+ a2e-γtcos(ωt)
4. Finally, plug in the values of a1 and a2 to verify Eqs. (9.34) and (9.35):
x(t) = x0e-γtcos(ωt)+ (v0 + γx0)e-γtsin(ωt)
v(t) = -γx0e-γtcos(ωt)+ (v0 + γx0)e-γtcos(ωt)
which are the same as Eqs. (9.34) and (9.35).
To learn more about oscillations refer :
brainly.com/question/30353823
#SPJ4
Desiccant failures arise when the system is left open for long periods of time and the
desiccant:
absorbs too much moisture.
becomes to dusty and dirty.
dries out too much.
is exposed to sunlight.
Desiccant failures can occur when the system is left open for long periods of time, allowing the desiccant to absorb too much moisture,
Desiccant failure refers to the inability of a desiccant material to effectively remove moisture from a system.
This can happen due to a variety of reasons such as the desiccant being saturated with moisture, becoming clogged with dust or dirt, becoming too dry, or being exposed to UV radiation.
This can lead to issues such as corrosion, mold growth, and reduced efficiency of the system.
Read more about machine failure here:
https://brainly.com/question/24885567
#SPJ1
the curren in a 60hz single phase lags 36 degress bnehind the voltage calculate the time interval between the posotive peaks of voltage and current
The time interval between the positive peaks of the voltage and the current is (360 - 36) / (2 x 60) = 5.0 seconds.
voltage and current in an AC circuit
The theory used in this question is the phase angle difference between the voltage and current in an AC circuit. The phase angle difference is the difference in the timing of the positive peak of the voltage and the positive peak of the current.
In this case, the phase angle difference is 36 degrees, which means that the current lags the voltage by 36 degrees.
To calculate the time interval between the positive peaks of the voltage and current, we use the formula: (360 - phase angle difference) / (2 x frequency).
In this case, the frequency is 60 Hz, so the time interval between the positive peaks is 5.0 seconds.
The steps for this process are as follows:
Step 1: Calculate the phase difference between the voltage and current:
The phase difference between the voltage and current is the difference between the angles at which they peak.
In this case, the voltage peaks at 0 degrees and the current peaks at 36 degrees,
so the phase difference is 36 degrees.
Step 2: Calculate the frequency of the voltage and current:
The frequency of both the voltage and current is 60 Hz.
Step 3: Calculate the time interval between the positive peaks of the voltage and current:
The time interval between the positive peaks of the voltage and current is equal to the phase difference divided by the frequency multiplied by two.
This gives us (360 - 36) / (2 x 60) = 5.0 seconds.
To learn more about AC circuit refer :
brainly.com/question/30353024
#SPJ4
The time difference between the positive voltage and current peaks is 5.0 seconds.
What is voltage and current in an alternating current circuit?The phase angle difference between voltage and current in an alternating current circuit is the theory used in this question. The phase angle difference is the difference in the timing of the positive voltage peak and the positive current peak.Here,
The phase angle difference in this case is given as, 36 degrees, indicating that the current lags behind the voltage by 36 degrees.
The time interval between the positive peaks of voltage and current is calculated using the formula: (360 - phase angle difference) / (2 x frequency).
Because the frequency in this case is 60 Hz, the time interval between the positive peaks is 5.0 seconds.
The following are the steps for this procedure:
Step 1: Determine the phase difference of the voltage and current:
The phase difference between voltage and current is defined as the angle at which they peak.
The voltage peaks at 0 degrees and the current peaks at 36 degrees in this case.
As a result, the phase difference is 36 degrees.
Step 2: Determine the voltage and current frequencies:
Both the voltage and current have a frequency of 60 hertz.
Step 3: Determine the time interval between the voltage and current positive peaks:
The phase difference divided by the frequency multiplied by two equals the time interval between the positive peaks of voltage and current.
This results in a time of (360 - 36) / (2 x 60) = 5.0 seconds.
To learn more about current refer to :
https://brainly.com/question/6944790
#SPJ4
take in a string from the user and split it into an array of single characters. split the list of characters into a list of lists where each inner list has 3 elements. notice that the last inner array may have fewer than 3 element
The split() method splits a string into an array of substrings. The split() method returns the new array. The split() method does not change the original string. If (" ") is used as separator, the string is split between words.
How do split a string into characters?Following are the program in Java Programming language
import java. util.*; //import package.
public class Main //define class main
{
public static Array List<Character>to Character Array(String s) //define function
{
Array List<Character> o b = new Array List<Character>(); //create Array List object.
for(char ch1: s.to Char Array())// iterating over the loop
{
ob. add(ch1); //add Character in list.
}
return o b; //return the object I. e return the value
}
public static void main(String arcs[]) // main method.
{
String str; // variable declaration.
int I; //define variable.
Scanner ob1 = new Scanner(System.in); //creating scanner class object.
System .out. print("Enter any string: "); //message
str = ob1.nextLine();//input value in str variable.
Array List<Character> ob2 = to Character Array(str); //create Array List reference variable and call to Character Array() function
System. out. print("Elements of the character array list: ");//message
for(I = 0;i<ob2.size();I++) //loop
{
Output:
Enter any string: Stony Brook
Elements of the character array list: S t o n y B r o o k
Explanation:
In the above java program firstly we import the package. Then we define a class that is "Main". In this class we define a function that is "to Character Array()" function and pass a string variable that is "s". After that, we create an Array List class object that is "o b" and define a loop. The loop is used to take input value and return its value.Then we define a main function. In the main function, we define a variable that is "i" and "str".Finally create an Array List object and use the loop for print inserted value with a separate of one space.To learn more about string refers to;
https://brainly.com/question/13972449
#SPJ4
in this diode circuit, what is the value of the load voltage v subscript r for v subscript i equals minus 5 v and v subscript i equals space 5 v? assume si diode with v subscript d 0 end subscript equals 0.7 space v. instructions: assume an on or off state for the diode and using the developed piecewise linear model for the diode, write the corresponding diode current and voltage equations for each state. write a kvl for the circuit and find the diode voltage and current. use the inequality in the piecewise linear model to check the calculated diode current or voltage values. the above steps should be repeated for each one of the given vi values. after you solved the problem, choose the option that has the correct statement. the statements in three out of four options are incorrect.
As a formula for current as a function of voltage, the ideal diode equation is quite helpful.When the ideal diode equation is reversed and used to solve for voltage as a function of current, we discover that v(i)=VTln[(iIS)+1).
How do you calculate the value of a diode?As a formula for current as a function of voltage, the ideal diode equation is quite helpful.When the ideal diode equation is reversed and used to solve for voltage as a function of current, we discover that v(i)=VTln[(iIS)+1). However, there are occasions when the inverse relationship may be more helpful.The voltage drop across the load when several diodes are connected in series is equal to (supply voltage - the number of diodes * 0.7).Taking figure 1 as an example, the voltage drop across the diode D1 is (5.0.7) = 4.3 V.D2 has a voltage drop of (5-2 * 0.7) = 3.6 V.Only the forward direction, also known as current flow, is allowed through a diode.To learn more about ideal diode equation refer
https://brainly.com/question/14894948
#SPJ4
Conider the following relational chema
Employee (empno, name, office, age)
Book (ibn, title, author, publiher)
Loan (empno, ibn, date)
Write the following querie in relational algebra.
• Find the name of employee who have borrowed a book Publihed by 1 McGraw-Hill?
• Find the name of employee who have borrowed all book Publihed by McGraw-Hill?
• Find the name of employee who have borrowed more than five different book publihed by McGraw-Hill?
Relational algebra is a procedural query language that consists of a set of operations used to manipulate and query data stored in a relational database.
The following queries in relational algebra:
1. σpublisher = “McGraw-Hill” (Book) ⨝ Loan ⨝ Employee (name)
2. σpublisher = “McGraw-Hill” (Book) ⨝ Loan ⨝ Employee (name) ⋈ Loan(empno)
3. σpublisher = “McGraw-Hill” (Book) ⨝ Loan ⨝ Employee (name) ⋈ Loan(empno) ⨝ σ Count(ibn) > 5 (Loan)
What is mean by relational algebra?
It is a formal language that uses mathematical notation and consists of a set of operations that act on one or more relations (tables) to produce new relations (tables). The operations include the usual set operations such as union, intersection, difference, and Cartesian product, as well as operations such as selection, projection, and join. Relational algebra is used to define the structure of a database, and to query and manipulate data stored in a database. The formal language is used to make it easier to understand and implement complex queries, as it allows for the expression of query logic in a more structured, logical form.
Relational algebra is useful for data manipulation, data exploration, and for expressing complex queries in a more structured way.
To learn more about relational algebra refer to:
brainly.com/question/10983796
#SPJ4
essential for organoid development and growth is a media composition that recapitulates the in vivo stem cell niche signalling pathways, able to sustain stem cell function and drive their expansion and eventually their differentiation
Organoids are 3D cell aggregates that are created in vitro from primary tissue or stem cells and have the ability to self-renew, self-organize, and demonstrate organ functions.
How does organoid development work?Organoid production is akin to organism development, which starts with a zygote and results in a fully developed adult organism. A variety of mature tissues are produced as a result of tightly regulated differentiation, proliferation, and apoptosis in conjunction with multicellular self-organization and patterning.Organoids are 3D cell aggregates that are created in vitro from primary tissue or stem cells and have the ability to self-renew, self-organize, and demonstrate organ functions.Human embryonic stem cells (ESCs) or induced pluripotent stem cells (iPSCs) can be used in vitro to produce intestine organoids instead of isolated intestinal stem cells.To learn more about stem cells refer to:
https://brainly.com/question/21222769
#SPJ4
Coal is being discharged from a first conveyor belt at the rate of 120 kg/s. It is received at A by a second belt that discharges it again at B. Knowing that v1 = 3 m/s and v2 = 4.25 m/s and that the second belt assembly and the coal it supports have a total mass of 472 kg, determine the components of the reactions at C and D.
To determine the components of the reactions at C and D, we need to use the equations of motion. We can use these equations to calculate the components of the reactions at C and D.
To calculate the components of the reactions at C and D, we need to first calculate the acceleration of the second belt assembly and the coal it supports. This can be done by dividing the difference in velocities (v2-v1) by the time it takes for the coal to travel from A to B. We can then use this acceleration to calculate the forces in the x-direction and the y-direction. The forces in the x-direction will be equal to the mass times the acceleration in the x-direction, and the forces in the y-direction will be equal to the mass times the acceleration in the y-direction. We can then use these forces to calculate the components of the reactions at C and D.
Learn more about equations of motion here
https://brainly.com/question/13514745
#SPJ4
What does it mean when it says an unknown being has entered this world in Blox fruit?
An unknown being has appeared in this world..."
This message only appears on the 3rd sea. The raid boss Soul Reaper has been reborn.
What does the world mean?
The word "world" refers to all that is, the totality of reality or the totality of beings. Different realms have developed different ideas about the world of nature. While some ideas regard the world as one, others refer to "many worlds". "Some people see the world as one simple thing, while others see it as a complex system with many moving parts. The term "world" or "universe" in scientific Cosmology refers to "[t]he totality of all space and time; all that is, was, and will be".
Potential worlds, on the other hand, are described as complete and coherent ways that things in modality theories would have can.
To learn more about world refer to
brainly.com/question/1892495
#SPJ4
pick a big problem in your school or your community that you think could be solved with the help of computer science, robotics, or hardware engineering.
Computer science or robots can even predict human behavior, which can aid in crime prevention.
What are the uses of computer science?We can predict hurricanes, tornadoes, and even the outbreak of a potentially fatal disease using these tools. It can even be used to predict human behavior, which can aid in crime prevention. Computer science has the potential to provide us with life-saving tools and work.AI is at the forefront of the digital transformation that is being used to solve some of the world's most pressing problems.Computer science has enabled the development of sophisticated tools that can aid in the resolution of environmental issues. Computers can easily handle issues such as pollution, waste management and disposal, disease identification and containment, and others.Learning about computer science is important and beneficial to all students because it drives innovation, discovery, and even political participation.To learn more about computer science refer to :
https://brainly.com/question/20837448
#SPJ4
etermine fcg and fgh , the magnitudes of the forces in members cg and gh, respectively, using the method of sections. assume for your calculations that each member is in tension, and include in your response the sign of each force that you obtain by applying this assumption.
All forces are pulling away from the thing when it is in tension. The pressures on the material push towards the direction of the body during compression.
A rope bridge can support both itself and its weight thanks to tension forces that pull and stretch material in opposing directions. Arch bridge rocks are forced to press against one another in order to support the weight due to compression pressures that squeeze and push material inward. Members can only be in compression or tension. When anything is under stress, all forces are repelled from it. When a material is compressed, the forces acting on it cause it to move in the direction of the body. Pulling on the ends of the object will increase the tension. All forces are pulled away from the object under tension, which is related to shifting the body's borders toward the centre. The pressures on the material push towards the direction of the body during compression.
Learn more about Compression here:
https://brainly.com/question/30115684
#SPJ4
EXAMPLE 1. 8 A current of 30. 0 mA is to be divided into two branch
currents of 20. 0 mA and 10. 0 mA by a network with an equivalent
resistance equal to or greater than 10. 0 N. Obtain the branch resistances.
COTTITION 1 g
The resistance in the branch with a current of 20mA is 10 ohms, and the resistance in the branch with a current of 10mA is 20 ohms.
What is the resistance about?We can use Ohm's law, which states that the current through a conductor between two points is directly proportional to the voltage across the two points, and inversely proportional to the resistance between them, to solve for the branch resistances.
I = V / R
Let R1 be the resistance in the branch with a current of 20mA and R2 be the resistance in the branch with a current of 10mA.
We know that the total current flowing through the network is 30mA and the equivalent resistance is greater than or equal to 10 ohms.
R_eq = (R1 + R2) >= 10 ohms
We also know that the current flowing through the two branches is equal to the total current flowing through the network.
I = I1 + I2
30mA = 20mA + 10mA
Now we can use the above equations to find the resistance of the two branches.
R1 = V / 20mA
= 10 ohms
R2 = V / 10mA
= 20 ohms
Learn more about ohms law from
https://brainly.com/question/231741
#SPJ1
See correct question below
A current of 30 mA is to be divided into branch currents of 20mA and 10mA by a network with an equivalent resistance equal to or greater than 10 ohms. Obtain the branch resistances.
how many centimeters are there in a length 32.7 inches ? express your answer in centimeters to three significant figures. activate to select the appropriates template from the following choices. operate up and down arrow for selection and press enter to choose the input value typeactivate to select the appropriates symbol from the following choices. operate up and down arrow for selection and press enter to choose the input value type nothing cm request answer sometimes you will need to change units twice to get the final unit that you want. suppose that you know how to convert from centimeters to inches and from inches to feet. by doing both, in order, you can convert from centimeters to feet. part b suppose that a particular artillery piece has a range r
In a length of 32.7 inches, there are 83.058 cm.
Explain about the centimeters?A centimetre is the unit of measurement for length in the metric system. One centimetre, which is equal to one hundredth of a metre, is denoted by the abbreviation "cm." Basically, 1 centimetre is equal to 0.01 metres, 10 millimetres, and 0.3937 inches.
An object's length is measured in centimetres, which are metric units of measurement. Cm is used to write it. Centimeters make up one metre. The length of a centimetre is 10 millimetres.
It is possible to refer to a centimeter as 10 millimeters. One centimeter about covers the width of a fingernail.
Inches should be multiplied by the conversion factor of 2.54.
So, 32.7 inches is 32.7 plus 2.54
= 83.1 580 millimeters
To learn more about centimeters refer to:
https://brainly.com/question/21386205
#SPJ4
0 shows a tank within a tank, each containing air. pressure gage a, which indicates pressure inside tank a, is located inside tank b and reads 5 psig (vacuum). the u-tube manometer connected to tank b contains water with a column length of 10 in. using data on the diagram, determine the absolute pressure of the air inside tank b and inside tank a, both in psia. the atmospheric pressure surrounding tank b is 14.7 psia. the acceleration of gravity is g
The acceleration of gravity is g = 32.2 ft/s2.
Why pressure gage a reads 5 psig (vacuum)?Absolute pressure of air inside Tank B = 14.7 psia + 5 psia = 19.7 psiaAbsolute pressure of air inside Tank A = 14.7 psia + 0.43 psia = 15.1 psia (Calculation: Pb = Patm + ρgh, where Pb = absolute pressure inside Tank B, Patm = atmospheric pressure, ρ = density of water, g = acceleration of gravity, and h = height of water column = 10 in. = 0.83 ft. Thus, Pb = 14.7 psia + (62.4 lb/ft3)(32.2 ft/s2)(0.83 ft) = 14.7 psia + 5 psia = 19.7 psia. Similarly, Pa = 14.7 psia + (62.4 lb/ft3)(32.2 ft/s2)(-0.43 ft) = 14.7 psia + (-0.43 psia) = 15.1 psia, where Pa = absolute pressure inside Tank A, and h = -0.43 ft = difference in water column heights.)The pressure gage a reads 5 psig (vacuum) because the pressure inside tank b is less than the atmospheric pressure surrounding tank b. Since the water in the U-tube manometer is in contact with the air inside tank b, the height of the water column is 10 in, which corresponds to a pressure difference of 10 in. Hg, or 5 psig. Therefore, the absolute pressure inside tank b is 14.7 psia – 5 psig = 9.7 psia, and the absolute pressure inside tank a is 9.7 psia + 5 psig = 14.7 psia. This is the same as the atmospheric pressure surrounding tank b.In summary, the pressure gage a reads 5 psig (vacuum) because the pressure inside tank b is lower than the atmospheric pressure surrounding it. This is indicated by the height of the water column in the U-tube manometer, which is 10 in, corresponding to a pressure difference of 10 in. Hg, or 5 psig. The absolute pressure inside tank b is 9.7 psia and inside tank a is 14.7 psia.To learn more about the pressure gage a reads 5 psig (vacuum) refer to:
https://brainly.com/question/13178456
#SPJ4
The air pressure surrounding tank b is lower than the pressure inside tank b, the pressure gauge a reads 5 psig (vacuum). The water column in the U-tube manometer is 10 inches high, which translates to a pressure difference of 10 inches of mercury, or 5 psig, when the water is in contact with the air in tank b. As a result, the absolute pressure inside tank b is 14.7 psia minus 5 psig = 9.7 psia, whereas the absolute pressure inside tank an is 9.7 psia plus 5 psig = 14.7 psia. This is the same as the pressure in the air around tank b.
To learn more about pressure gauge refer to:
https://brainly.com/question/13292088
#SPJ4
Element-wise division: Convert pounds to kilograms Assign row array weightKilo with the corresponding weight in kilograms. Use the following conversion: kg = lb / 2. 2 Function Save Reset MATLAB DocumentationOpens in new tab function weightKilo = ConvertToKilo(weightPounds) % weightPounds: Row array of weights in pounds % Assign weightKilo with the corresponding weight in kilograms weightKilo = weightPounds; end 1 2 3 4 5 6 7 Code to call your function
Go to the Home tab and select NewScript or New Live Script to create a script or live script with local functions.
How should you use functions in a MATLAB script ?
Go to the Home tab and select NewScript or New Live Script to create a script or live script with local functions. Then paste the code into the file. After the script code, place any local functions at the end of the file.
Add at least one line of script before the local functions.
Function weight Kilo = Convert to Kilo (weight Pounds)
weight Pounds: array of lines with weights in pounds
weight Assign kilo from corresponding weight in kilogram
weight Kilo weight lbs/2.2 ; divides each element of the Pounds Weight array by 2.2.
End.
To learn more about function refer to:
brainly.com/question/25324400
#SPJ4
You are working with a database table that contains employee data. The table includes columns about employee location such as city, state, country, and postal_code. You want to retrieve the first 3 characters of each postal code. You decide to use the SUBSTR function to retrieve the first 3 characters of each postal code, and use the AS command to store the result in a new column called new_postal_code. You write the SQL query below. Add a statement to your SQL query that will retrieve the first 3 characters of each postal code and store the result in a new column as new_postal_code. NOTE: The three dots (...) indicate where to add the statement.
Include a clause that will extract the first three letters of each country's name and place the results in a new column called "new country" in your SQL query.
From customer data, SELECT new country AS SUBSTR (country, 1, 3). For each item in the "customer data" database, the first three letters of the country's name will be extracted, and the data will be saved in a new column called "new country." You can then filter, sort, or group the data based on the first three letters of the nation name using this column in your query. You may use the following syntax to add a statement to your SQL query that will get the first three letters of each country name and put the information in a new column called "new country";
Learn more about SQL query here:
https://brainly.com/question/30115014
#SPJ4
when a technician purchases a gas furnace, it is set up to run on natural gas. a technician purchases a conversion kit. what would the technician expect to find in the conversion kit?
Answer:
A new burner orifices: These are small openings in the burner assembly that allow the correct amount of gas to flow into the furnace. The orifices in the kit will be different than the orifices in the natural gas furnace, as they are designed to work with the different pressure and flow rate of propane.
A new gas valve: The gas valve controls the flow of gas into the furnace. The gas valve in the conversion kit will be designed to work with propane, as it will have different pressure and flow characteristics than the natural gas valve.
A new regulator: This component reduces the pressure of the gas as it enters the furnace. The regulator in the conversion kit will be designed to work with propane, as it will have different pressure and flow characteristics than the natural gas regulator.
Instructions and documentation: The conversion kit should include detailed instructions and documentation on how to safely and correctly convert the furnace. This documentation should include all the necessary information such as safety precautions, tools needed, and step-by-step instructions.
In addition to the components mentioned above, the technician should also expect to find any additional parts or components that are required to complete the conversion process safely and efficiently. This can include, but not limited to, the venting system, any electrical components or wiring, and any additional hardware needed to complete the conversion.
It's important to note that the conversion process requires expert knowledge, skills and experience, and should only be carried out by a qualified and experienced technician. Additionally, the technician should follow the manufacturer's instructions and comply with local codes, regulations and safety standards
A circuit consists of five elements. How much power is dissipated or delivered by element 5 if element 1 is delivering P1 = 730 mW of power, element 2 is absorbing P2 = 762 mW of power, element 3 is absorbing P3 = 170 mW of power, and element 4 is delivering P4 = 820 mW of power.
The power dissipated or delivered by element 5 can be calculated by subtracting the power absorbed by elements 1, 2, and 3 from the power delivered by element 4.
Therefore, the power dissipated or delivered by element 5 is P5 = P4 - (P1 + P2 + P3) = 820 mW - (730 mW + 762 mW + 170 mW) = -32 mW. This means that element 5 is absorbing 32 mW of power.The power dissipated or delivered by element 5 can be calculated by subtracting the power absorbed by elements 1, 2, and 3 from the power delivered by element 4. Therefore, the power absorb delivered by element 5 is P5 = P4 - (P1 + P2 + P3) = 820 mW - (730 mW + 762 mW + 170 mW) = -32 mW. This means that element 5 is absorbing 32 mW of power. This is because the total power absorbed by elements 1, 2, and 3 is greater than the power delivered by element 4. Therefore, element 5 must absorb the difference in order to maintain the balance of power in the circuit.
Learn more about power here
https://brainly.com/question/30150415
#SPJ4
you are the network administrator for a branch office of a larger organization. your branch is adding a new wireless network into an existing branch office lan. the existing network is configured to exchange routes using ospfv2 in a single-area configuration. your task is to verify the operation of the existing ospfv2 network, before adding in the new lan. when you are sure that the current ospfv2 lan is operating correctly, you will connect the new lan and verify that ospf routes are being propagated for the new lan. as branch office network administrator, you have full access to the ios on routers r3 and r4. you only have read access to the enterprise lan routers r1 and r2, using the username branchadmin, and the password branch1234.
One of those is accurate since the two routers cannot become neighbors because they have the same OSPF router ID (RID).
An OSPFv2 router broadcasts a distinct message, known as a hello packet, out each OSPF-enabled interface in order to identify other OSPFv2 neighbor routers. Following the discovery of a neighbor, the two routers compare information from the hello packet to determine whether their configurations are compatible. The default network type for an Ethernet interface that supports OSPF is the broadcast network type. A connection capable of supporting Layer 2 broadcast is required. Neighbors are two or more routers sharing an interface in a shared network, such as two routers connected via a point-to-point serial link. One of those is accurate since the two routers cannot become neighbors because they have the same OSPF router ID (RID).
Learn more about Router here:
https://brainly.com/question/29511214
#SPJ4
Imagine that NASA has funding for only one telescope. The three following proposals are submitted. Which one will be most successful?a. an X-ray telescope located in Antarcticab. a radio telescope in space that orbits Earthc. a near-infrared telescope on a mountaintop inChile
The most successful proposal is likely to be the radio telescope in space that orbits Earth.
This is because a radio telescope in space is able to observe signals from farther away, including from galaxies and objects outside our own. Additionally, it is not limited by the weather or other environmental factors on Earth, as space-based telescopes are able to operate uninterrupted. This makes it an ideal choice for NASA's limited funding.
NASA, or the National Aeronautics and Space Administration, is the United States government agency responsible for the civilian space program, as well as aeronautics and aerospace research. NASA was established in 1958, and since then it has been responsible for a number of revolutionary advancements in space exploration, including the first human landing on the moon and the development of the Space Shuttle.
Learn more about NASA:
https://brainly.com/question/1350178
#SPJ4
n this lab, you task is to diagnose and correct the problem. use the following steps to walk through the troubleshooting process: press the power button on the computer to verify that it will not start. select the motherboard and view the specifications to identify the location of the cpu socket and fan power connector. answer question 1. close the motherboard specs and verify that the cpu heat sink and fan assembly is installed. answer question 2. answer question 3. based on your findings, you will need to replace the cpu. temporarily remove the heat sink and fan to the workspace.
An approach to problem solving called troubleshooting is frequently used to fix broken components or operations on a machine or a system.
What are the 7 troubleshooting steps?The next seven steps are frequently employed during troubleshooting, however troubleshooting approaches differ.Acquire knowledge.Write about the issue.The most likely reason should be determined.Making a plan of action and putting a fix to the test.Activate the solution.Speculate on the findings.Make a process record. In order to discover the source of the aforementioned situation, one must first establish a theory of probable causation, test that theory, and then follow the steps outlined above once they have done so.Computer troubleshooting is a term that refers to a methodical approach to problem-solving that is stated to be frequently used to identify and resolve problems with sophisticated machinery, electronics, computers, and software systems.To learn more about troubleshooting refer
https://brainly.com/question/28508198
#SPJ4
Struggling to stay faithful and remain attracted to my (34M) wife (28F) after we experienced a violent attack together. Not sure what to do.
The man's wife jumps in front of him to protect him from an attacker and has a scar on her face. The man finds his wife less attractive and "tries" to remain faithful to her. He is also annoyed that instead of spending the money to look better, she wants to keep it for her son.
What does money mean?
Currency is a commodity generally recognized as an economic medium of exchange. It serves as a means of expressing values and setting prices. It is the primary indicator of wealth as it moves from person to person and country to country. others that enable trade. According to economists, there are four basic types of money: commercial money, fiat money, fiat money, and commodity money. Commodity money is money whose value is derived from the commodities that compose it. Money is a centralized, widely used, and accepted form of exchange that facilitates the exchange of goods and services.
In economics, money is used as a medium of exchange for various goods and services.
To learn more about money refer to
brainly.com/question/24373500
#SPJ4
A circular bar supports an axial force of 39 KN. If the compressive stress in the bar is not to exceed
80 MN/m2, determine the diameter of the bar.
The diameter of the bar is 55.85 KN
What does "bar diameter" mean?A circular bar supports an axial force of 39 KN. If the compressive stress in the bar is not to exceed 80 MN/m2,
If you want to get the nominal diameter in inches, multiply the bar size by 80/39. For instance, the diameter of #8 rebar is 80/39 inches (or 1 inch). The weight, nominal area, and nominal diameter are common metrics.
The formula below may be used to determine the minimal diameter of round bar given the width and height of flat bar. Square Bar Minimum Diameter = Square Root of Flat Bar's Width and Height in Inches.
[tex]\sqrt{}[/tex]80 * 39 = 55.85
The diameter of the bar is 55.85 KN
To learn more about diameter refer to:
https://brainly.com/question/23220731
#SPJ4
PS.52 The Station, a boutique cookie company, needs to create a production process for its new cinnamon malt ball cookies. To help accomplish this, the company has put together some numbers for production costs (per dozen cookies for the variable costs). Pre-Bake$150 Fixed Costs $1.75 Labor Costs $0.59 Material Costs Easy Bake$350 Fixed Costs $1.53 Labor Costs $0.48 Material Costs Speed Bake$550 Fixed Costs $1.35 Labor Costs $0.48 Material Costs The Station projects demand for the semester will be 450 dozen cinnamon malt ball cookies. Due to the cookies' expected popularity the selling price will be $4.49.A. Based on the projected demand (volume) for the semester, which process type should they select?1. Pre-Bake2. Easy Bake3. Speed BakeB. Under this process type—the one selected in the previous question—what would be their profits for the semester? (Display your answer to one decimal place.)C. If demand were to increase, what would be the break-even point (in unit volume or demand) between the selected process and the next process option? (Display your answer to two decimal places.)D. Beyond this break-even point, which process would be best?1. Pre-Bake2. Easy Bake3. Speed BakeE. Based on the break-even point (derived two questions back), what would be the total cost? (Display your answer to two decimal places.)
After an analysis of the costs, the demand, and the types of processes, the best cookie production option depends on the demand. Answer: If the demand is from 1 dozen to 600.06, pre-bake is selected, if it is greater, easy-bake. An image of the calculation procedures is attached
Which process type should they select?The best process type is the pre-bake because it has the greatest profits, as shown in the attached figure.
What would be their profits for the semester?For the pre-bake type process, the semester benefit is $817.50.
What would be the break-even point between the pre-bake and easy-bake process option?The semester demand would have to be 600.06 dozen cookies so that the pre-bake process is no longer the best option but easy-bake. Below is the solution algorithm.
Python codeif __name__ == '__main__':
fixed_cost_prebake = 150
fixed_cost_easybake = 350
variable_cost_prebake = 2.34
variable_cost_easybake = 2.01
sales_price = 4.49
profit_prebake = 0
profit_easybake = 0
sales = 0
while True:
sales = sales+0.01
profit_prebake = fixed_cost_prebake+(variable_cost_prebake*sales)
profit_easybake = fixed_cost_easybake+(variable_cost_easybake*sales)
if profit_prebake>=profit_easybake: break
sales = int(sales*100.0)/100.0
print("Break Even Point")
print("The demand would have to be: ",sales," so that pre-bake is no longer the best option but easy-bake")
Beyond this break-even point, which process would be best?When the demand is greater than 600.06 dozen, the best option is easy-bake process.
To learn more about analysis of the demand see: https://brainly.com/question/14570490
#SPJ4
what is the most important step in safely changing lanes
Answer:
The most important step in safely changing lanes is to check your mirrors and do a shoulder check to ensure it is safe to do so. This includes checking for vehicles in your blind spot, as well as checking for any pedestrians, bicycles, or other obstacles that may be in the way.
The most critical step in safely changing lanes is checking your blind spots. It's an area that your mirrors cannot cover and so you have to briefly look over your shoulder to ensure there's no vehicle in that space before changing lanes.
Explanation:The most important step in safely changing lanes is to check your blind spots. This is significant because there might be another vehicle or obstacle in the area of the road you cannot see either through your peripheral vision or rear-view mirrors. Here are the steps you should follow when changing lanes:
Turn on your signal to indicate your intention to other drivers.Check your rear-view mirror and side mirrors to see if the lane is clear.Next, check your blind spot. This is done by briefly looking over your shoulder in the direction you intend to move.Only when you’re sure the lane is clear, carefully change lanes.Make sure to revert to your original lane once you have completed the maneuver.Learn more about Changing lanes safely here:https://brainly.com/question/31918423
#SPJ6
which of the following securities is (are) not considered to have an issuer? i collateral trust certificate ii equipment trust certificates iii fractional interests in oil and gas programs iv certificates of interest in a gravel mining program a i and ii only b iii only c iii and iv only d i, ii, iii, iv
Mortgage bonds, collateral trust certificates, and income bonds are examples of securities issued by corporations
The bond, whether municipal, corporate, or government-issued, is one of the most often used types of debt securities. Other unique categories of debt instruments exist, meanwhile, including assets backed by mortgages, CDOs, preferred stock, and euro commercial paper. A corporate bond is one type of financial asset in particular that is sold to investors. In return for lending the company the money it needs; the investor receives a predetermined quantity of interest payments at either a fixed or variable interest rate. When the bond stops receiving payments and the original investment is returned, it has "matured." Mortgage bonds, collateral trust certificates, and income bonds are all types of debt instruments that corporations issue. Revenue bonds are not issued by corporations.
Learn more about Securities here:
https://brainly.com/question/29510297
#SPJ4