Experimental Design Application Production engineers wish to find the optimal process for etching circuit boards quickly. They create a single replicate 24experiment to test the effect of the following factors on time to etch a circuit board: (A) Concentration of nitric acid in the etchant, (B) temperature of the etchant, (C) stirring rate in the etching tank, (D) surface area of the board. Running this experiment, they obtain the data in HW_EDA_137.csv.Preview the document Which factors effects and interaction effects are significant?

Answer:

some part of your question is incomplete

attached below is the complete question

Answer :

F(0) = -5  < 0

F(1) = e - 1 > 0

since the functions : f(0) and f(1) have opposite signs then there is a 'c' whereby F(c) = 0 ( intermediate value theorem fulfilled )

Hence there is a root in the given equation : [tex]e^x = 6 - 5x[/tex]

Explanation:

using Intermediate value Theorem

If F(x) is continuous and f(a) and f(b) have opposite signs then there will be a'c'E (a,b)  whereby F(c) = 0

given equation : [tex]e^x = 6 - 5x[/tex]   on (0,1)

and F(x) = [tex]e^x - 6 + 5x = 0[/tex]

This shows that the F(x) is continuous on (0,1)

F(0) = [tex]e^0 - 6 + 5(0)[/tex]  = -5 which is < 0

F(1) = [tex]e^1 -6 + 5(1)[/tex] = e -1 > 0  and e = 2.7182

since the functions : f(0) and f(1) have opposite signs then there is a 'c' whereby F(c) = 0 ( intermediate value theorem fulfilled )

Hence there is a root in the given equation : [tex]e^x = 6 - 5x[/tex]

Answer:

1. They needed to develop multiple components in software programs.

2. The ability to overlap the development to be more evolutionary in nature.

3. The need to be more risk-averse or the unwillingness to take risks led to the use of a spiral model.

Explanation:

Software development life cycle (SDLC) can be defined as a strategic process or methodology that defines the key steps or stages for creating and implementing high quality software applications.

In SDLC, a waterfall model can be defined as a process which involves sequentially breaking the software development into linear phases. Thus, the development phase takes a downward flow like a waterfall and as such each phase must be completed before starting another without any overlap in the process.

An incremental model refers to the process in which the requirements or criteria of the software development is divided into many standalone modules until the program is completed.

Also, a spiral model can be defined as an evolutionary SDLC that is risk-driven in nature and typically comprises of both an iterative and a waterfall model. Spiral model of SDLC consist of these phases; planning, risk analysis, engineering and evaluation.

What motivated software engineers to move from the waterfall model to the incremental or spiral model is actually due to the following fact;

The final specific internal energy : 190 kJ/kg

The laws of thermodynamics 1 state that: energy can be changed but cannot be destroyed or created  

The equation is:  

[tex]\tt E_{in}-E_{out}=\Delta E~system\\\\\Delta E=\Delta U+\Delta KE+\Delta PE\\\\\Delta U=m(U_2-U_1)\\\\Q-W=\Delta U+\Delta KE+\Delta PE[/tex]  

Energy owned by the system is expressed as internal energy (U)  

This internal energy can change if it absorbs heat Q (U> 0), or releases heat (U <0). Or the internal energy can change if the system does work or accepts work (W)  

The sign rules for heat and work are set as follows:  

• The system receives heat, Q +  

• The system releases heat, Q -  

• The system does work, W -  

• the system accepts work, W +  

A closed system of mass 20 kg⇒m=20 kg

Heat transfer of 1000 kJ from the system to the surroundings⇒Q=-1000 kJ

The work done on the system is 200 kJ⇒W=+200 kJ

The initial specific internal energy of the system is 250 kJ /kg⇒U₁ = 250 kj/kg

Neglect changes in kinetic and potential energy⇒ΔKE+ΔPE=0, so

Q-W = ΔU

Input in equation

[tex]\tt -1000-200=20(U_2-250)\\\\-1200=20U_2-5000\\\\3800=20U_2\\\\U_2=190~kJ/kg[/tex]

Explanation:

10000=5000(1.12^x)

2=1.12^x

(log_1.12)(2)=x

x= about 6.1163

10000=5000(1.2^x)

2=1.2^x

(log_1.2)(2)=x

x= about 3.8019

compare them by saying like 20% will be 6.12/3.8 times faster

Answer:

Both Technicians A and B  are correct

Explanation:

If the fluid pressure will decrease quickly in a car when the ignition says that one or more has been switched off. One or two could be leaking or the source could be a faulty check mechanism in the catalytic converter.

Answer:

Yes, this is completely independent.

Explanation:

Yes, this is completely independent. Even though there are no South American individuals that are majoring in biomedical engineering in this party it is still a completely independent factor. The origin of birth of an individual does not tie them to a specific degree or field of expertise, therefore a South American individual can study anything they want including mechanical engineering, electrical engineering, or biomedical engineering.

Answer:

B. Precisely define the problem that is to be solved.

Explanation:

Engineering can be defined as the scientific and technological principles that is used for the design, development, operation and control of tools, machines or equipments, structures and systems. These machines, tools, systems and structures are typically designed and developed for the purpose of solving peculiar problems relating to human life. Simply stated, engineering is focused on proffering solutions to real life problems through a design process.

Generally, the design process comprises of series of steps used for the development of various tools, machines, structures and systems. In a chronological order, the basic steps of a design process are;

1. Define the problem: to proffer a solution to any problem, you have to precisely define the problem that is to be solved. Therefore, this is the first step of the design process.

2. Conduct a research: the engineer should collect or gather data (informations) relating to the project.

3. Brainstorming and analysis of data: this is the stage where the engineer conceptualize his or her ideas.

4. Create a prototype or simulated model of the product.

5. Product analytics and test: this is where the product is being used and tested for any flaw, error or defects. Thus, troubleshooting is also required at this stage.

Hence, if an engineer is trying to build a new measurement tool; the first step the engineer should complete is to precisely define the problem that is to be solved so as to have a good clear-cut understanding of the problem.

Answer:

Explanation:

One number is wrong; they all lack units.

The basic ratio is 1" = 20', so you can divide feet by 20 to find inches.

Perhaps you want decimal inches: