Lateral runout can be felt in the steering wheel even when the vehicle is
Select one:
a. At slower speeds
b. Just starting to move away from a stop
C. Just coming to a stop
d. Stopped
Lateral runout is felt in the steering wheel even at slower speeds. It leads to riding vibration and therefore poor ride quality.
Lateral runout refers to the side-to-side movement of the car's rotor as it rotates, which is caused by the off-center deviation of the rotor.
Lateral runout leads to riding vibration and therefore it is associated with poor ride quality.
Lateral runout can be properly quantified by using a dial indicator, which is a precision device used to measure linear displacements.
Learn more about lateral runout here:
https://brainly.com/question/21094536
In order to write a good problem statement, you need to identify the following components of the problem.
who, what, when, how
O True
O False
Answer:
True.
Explanation:
12. How will the temperature change in a room with an open refrigerator door, once equilibrium is established
Answer:
then back into the room
Explanation:
If you leave the door open, heat is merely recycled from the room into the refrigerator, then back into the room. A net room temperature increase would result from the heat of the motor that would be constantly running to move energy around in a circle.
Over 30 day period, a lake surface area is 1260 acres. The inflow is 36 cfs, thee outflow is 30 cfs. Seepage loss is 1.5 in. The total precipitation is 4.0 in. Evaporation loss is 6.0 in. Determine the water level change (inch) for the lake during this period.
Answer:
-0.1 inches
Explanation:
The net inflow is ...
36 cfs -30 cfs = 6 cfs
The number of seconds in 30 days is ...
(3600 s/h)(24 h/da)(30 da) = 2,592,000 . . . . seconds/(30 days)
Then the volume of inflow is ...
(6 ft^3/s)(2,592,000 s) = 15,552,000 ft^3
The number of square feet in 1260 acres is ...
(1260 ac)(43560 ft^/ac) = 54,885,600 ft^2
So, the increase in depth due to the inflow is ...
(15,552,000 ft^3)/(54,885,600 ft^2) ≈ 0.283353 ft ≈ 3.4002 in
__
The net change in water level is then ...
inflow - seepage + precipitation - evaporation
3.4 in -1.5 in +4.0 in -6.0 in = -0.1 in
The water level change in the period is -0.1 inch.
How to make this circuit for simulating on Proteus.
Write a program that computes the square footage of a house given the dimensions of each room.Have the program ask the user how many rooms in the house and then request the dimensions of eachroom. Display the resulting total square footage.
What are minerals made of?
NO LINKS PLEASE
A. Different substances
B. Liquid substances
C. Two or more substances
D. The same substance throughout
Answer:
the answer I know is A. different substances. hope this helps :).
Explanation:
just always study hard and God bless.
PDC Bank is working on creating an AI application that enables customers to send SMS to the AI application to allow banking activities from their registered ID. Jane, the project engineer, has taken bank customer data from the last few years from the server and is using it to train the ML to recognize and authenticate actual users and to ensure unauthorized users are barred from entering the application. Suppose the AI application has been compromised, and the reason has been identified as compromised data being used to improve the ML accuracy. What kind of attack is the PDC Bank application subjected to?
The kind of attack that the PDC Bank application is subjected to due to compromised data is: Adversarial artificial intelligence
Adversarial artificial intelligence is a form of attack on a neural network where a wrong algorithm is entered into the system to deceive the end user.
The aim of this machine learning method is to deceive the end user.
This is what happens to the PDC Bank when its data was compromised in the course of improving the machine learning accuracy.
Learn more about Adversarial artificial intelligence here:
https://brainly.com/question/22190244
How can we honor what we value and care about in a world of disruptive technologies like AI?
Answer: Well, that's a good question. When we look around us, we tend to see what technology has done for us, and how far it is taking us. It might be disruptive, but without it there would be no high tech military weapons, and then how would we defend ourselves? There would be no technology entertainment and without that, life would be very dull. In answering your question, we can be thankful for what it is and how far it has been taking us in life.
Explanation: Please mark a brainliest if correct it helps and have meery holidays!
Two students are discussing weathering and erosion factors. Leah says that both weathering and erosion involve wind, water, and ice. Justin says that only weathering involves ice, and that erosion involves plants and animals. Who is correct?
A. Justin, because plants cause erosion too.
B. Justin, because erosion does not involve ice.
C. Leah, because she forgot to mention plants and animals.
D. Leah, because glaciers are ice that cause erosion too.
Answer: Justin is false and it is both bottom because plants and animals are helpless to erosion and we cause it by deforestation and weather does too
Explanation:
Justin, because plants cause erosion too factors. This was the statement are the correct. Thus, option (a) is correct.
What is erosion?The geological process through which earthen elements are worn down and transferred by wind and water or water is known as erosion. The migration of nanoparticles away from their origins is referred to as erosion. Erosion is the loss of dirt, rock, or dissolved substances by surface processes.
According to the two students are the different in the studies. There was the based on the Leah are the said on the different in the concept and the Justin said into the different in the concept are the perception of the topic are the different. Justin was the correct because plants are the cause of erosion too factors.
As a result, the Justin, because plants cause erosion too factors. Therefore., option (a) is correct.
Learn more about on erosion, here:
https://brainly.com/question/3852201
#SPJ2
Rocks in mountains can be weathered by breaking them apart. How can they be eroded?
A. Pieces of rocks are moved by the deep roots of plants.
B. Pieces of rocks are moved by water and gravity.
C. Rocks expand by the temperature changes in the mountains.
D. Rocks are smoothed by the flowing water and ice.
NO LINKS PLEASE!
Answer: If you look up its definition of eroded it'll tell you the answer should be B
Explanation:
A fully charged battery with 6 cells should indicate
Answer:
Battery Voltage
Voltage refers to the amount of electrical potential your battery holds. The standard automotive battery in today's vehicles is a 12-volt battery. Each battery has six cells, each with 2.1 volts at full charge. A car battery is considered fully charged at 12.6 volts or higher.
Which of the following is a measurement at the nominal level?
A-personal income in a year
B-student grades
C-the color of a person's hair (blond, brunette, redhead)
D-temperature
Answer:
A-personal income in a year this is the answer
Describe two fundamental reasons why flexural strength should depend on porosity
Answer: The elastic modulus and flexural strength are found to decrease with increased porosity. Fractography studies have been undertaken to identify the role of the pores on the fracture path. The deflection and cracking behavior of concrete structure depend on the flexural tensile strength of concrete. Many factors have been shown to influence the flexural tensile strength of concrete, particularly the level of stress, size, age and confinement to concrete flexure member, etc.
Explanation:
An unknown relative passes away and bequeaths upon you a small tract of land in Amherst. You decide to build a two-story storage facility to make the best of your bequest. But your self-storage dream is in jeopardy due to a 10 meter thick layer of soft clay (N<4) on the site. You put on your best geotechnical engineer hat, hire a driller to pull up some samples, and send them off to a lab for a consolidation test. The report indicates that the clay is a dark grey, slightly sweet, kaolinite blend with a cy = 1x10-7 mº/s, single-drained, and an ultimate settlement of 0.73 meters. It does not make financial sense to install deep foundations, so you are interested in how long it will take to consolidate the clay layer using a passive load.
How long will it take for settlements of 25, 50, and 65 cm to occur?
If you need to build within the next 12 months and have at least 65cm of settlement to be viable, does it make sense to proceed?
Answer: It does make sense, because I've been involved in these careers and have a long family line of them. And other questions?
Explanation:
As part of the overall systems engineering process, there are a variety of software development methods, but the three most common at DoD are the Waterfall Approach, the Incremental Approach, and the ______________ Approach.
The three most common software development methods are the Waterfall Approach, the Incremental Approach, and the SPIRAL Approach. These methods depend on the team size and specific goals.
Software development is the sequential procedure that involves the division of the work into smaller and parallel stages in order to improve software design and product management.
The software development methods depend on both the team size and specific objectives.
The most common methodologies for software development include:
Waterfall Spiral Incremental Agile Continuous integrationLearn more about software development here:
https://brainly.com/question/14275830
10. Which is of the following is not used in the
testing/analysis step?
A. Engineering notebooks.
B. Multiview drawings.
C. 3-D modeling software.
D. CNC machines.
A CNC machine stands for Computer Numerically Controlled Machine, they are used to Machine objects in hence create items, machine parts from prototypes. Hence the CNC machines are not used for testing/Analysis
D. CNC machines.
In Engineering the following items are basically needed for and during test/Analysis
Engineering notebooks: This is used to write down importance observations and findingsMulti-view drawings: This is also needed to visualise prototypes from different perspective or views3-D modelling software: e.g AutoCad , Autodesk Inventor, Revit to mention a few can be used to design and analyse project even before their actual implementation or designLearn more:
https://brainly.com/question/9275741
need help answering this question
Answer: Wow. I just did that not so long ago. The mean is 76, i think the deviation is 73 and ill recall my notes for the next, hold on
Explanation:
What effect did the Ice Age have on early humans
Answer:
The development of homosapiens
Explanation:
People adapted to the harsh weather by creating tools and used land bridges to spread to new regions
All of the following are employment requirements for a technician EXCEPT:
Select one:
a. Being drug and alcohol free
b. Having all of your ASE certifications
c. Having a clean driving record
O d. Having honesty, integrity, reliability, and quality
Answer:
I think it would be C but im not sure sorry if its wrong
6.03 Discussion: Then & Now - Safety
Discussion Topic
I'm Done
In this unit, you have learned about the evolution of the industry’s machines, through both technology and innovation. These improvements have reduced risk and injury to the Operating Engineers.
Choose one innovation or device.
Explain why you think that technology is the most important advancement in Operating Engineers’ safety.
Answer:
Information technology is important in our lives because it helps to deal with every day's dynamic things. Technology offers various tools to boost development and to exchange information. Both these things are the objective of IT to make tasks easier and to solve many problems.
4. What is the ampacity of 8-gage copper wire?
O A. 45 amps
OB. 30 amps
O C. 50 amps
O D. 25 amps
The section 5(a)(1) of the osh act is commonly known as
Answer:
general duty clause
Explanation:
Marketing in the fresh produce industry does not include buying, selling,
transportation or pricing?
Answer: I personally believe it does, because the Circle of Life, or what I think, at least buying and selling
Explanation:
Why is the tensile strength of a material important to consider when building a structure? Answer in a one page essay!!!
Font
Paragraph
Styles
Editing
(1) What are the available methods for crop establishments in the field?
(2) Give a conceptual sketch for a seeder to establish soybean seeds in an
agricultural field of dry zone in Sri Lanka (Use software where
necessary/or a hand sketch with detail).
(3) Discuss the advantages of the seed dibbling mechanism and list the
crops that can be used dibbler.
A
(4) Discuss the key points to enhance agricultural productivity using the
fertilizer applicators.
(5) Calculations: Calibration of a seed drill
Number of furrows = 5
Spacing between the furrows = 8 cm
Diameter of the ground wheel = 0.65 m
Number of rotations of the ground wheel = 300
Weight of seed collected = 20 kg
Calculate the seed rate in kg/ha
The average number of seeds dropped per one revelation =6
Calculate the
(1) seed rate and
(ii)
hole to hole spacing
Answer:
1) Therefore it was so much more than one answer my headWho is responsible for shielding a welding arc to protect
the eyes and skin of all persons in the working area?
Answer:
manager and supervisor
Explanation:
a. State the functions of the followings
a. Commutator
b. Armature core
c. Field system
d. Brushes
e. Armature winding
Answer:
a. State the functions of the followingsa. Commutator:
the commutator reverses the current direction with each turn serving as a mechanical rectifier to convert the alternating current from the windings to unidirectional direct current in the external load circuit.
b. Armature core
Armature core is a physical structure made up of silicon steel stampings. The core is laminated to keep iron losses low. Armature winding is the main current carrying winding where we either provide(electric supply to motor) or extract e.m.f(collect electric power from generator).
c. Field system
The field winding basically form an electromagnet, that produces field flux within which the rotor armature of the DC motor rotates, and results in the effective flux cutting
d. Brushes
The function of brushes is that the brushes conduct current between stationary wires and moving parts of the electric Generator.
e. Armature winding
The winding wound on the core is given current through a DC supply. This current-carrying winding as under the influence of the magnetic field develops a force that develops a rotational torque. This torque enables the machine to rotate.
[tex] \bold \pink{ \underline{hope \: it \: helps}}[/tex]
The customer you were waiting on is nodding while listening to you and gesturing when he speaks what type of language does this represent
Explain the conditions under which galvanic corrosion occurs
Answer:
Explanation:
Galvanic corrosion occurs when two dissimilar metals are immersed in a conductive solution and are electrically connected. One metal (the cathode) is protected, whilst the other (the anode) is corroded. The rate of attack on the anode is accelerated, compared to the rate when the metal is uncoupled.