3.33 MPa is the maximum bearing stress on the concrete footing. A footing that is 525 mm x 525 mm in dimension will have an average bearing stress of 145 kPa.
Find the maximum bearing stress?A) 3.33 MPa is the maximum bearing stress on the concrete footing.
B) A footing that is 525 mm x 525 mm in dimension will have an average bearing stress of 145 kPa.
A) The footing image is missing, therefore I have attached it.
The short wooden post's measurements, according to the provided image, are;
120 mm wide equals 0.12 meters.
length is 100 mm, or 0.1 m.
the wooden post's vicinity is;
A = 0.12 × 0.1
A = 0.012 m²
Maximum bearing stress is calculated as follows:
σ max = F/A
We receive; F = 40 kN = 40 000 N is the force.
Thus;
σ max = 40000/0.012
σ max = 3.33 × 10⁶ Pa
3.33 MPa for _max
B) The average bearing stress is reportedly 145 kPa (145000 Pa) at this time.
In light of the fact that A = b2, = F/A 145000 = 40000/A (since the footing is square)
The result is that b2 = 40000/145000 b2 = 0.2758620689655 b = 0.2758620689655 b = 0.525 m b = 525 mm.
To learn more about maximum bearing stress refer to:
https://brainly.com/question/16929901
#SPJ4
when seating the brake pads just installed in the brake calipers, a technician should place his or her left foot under the brake pedal so that when applying the pedal with the right foot, the pedal does not push the master cylinder farther into the master cylinder bore, which could: group of answer choices dislodge sludge. cut the lips of the master cylinder primary seals. both a and b none of the above
The pedal does not push the master cylinder farther into the master cylinder bore.
What is the advantage of using a left foot?
The theory used in this question is the principle of using a left foot to apply pressure to the brake pedal while seating the brake pads. By using the left foot on the brake pedal while the right foot applies pressure, the technician is able to prevent the master cylinder from being pushed farther into the master cylinder bore.
The steps for this process are as follows:
1. Place the brake pads into the caliper.
2. Place the left foot on the brake pedal.
3. Use the right foot to apply pressure to the pedal, pushing it down slowly.
4. Allow the pressure from the left foot to prevent the master cylinder from being pushed farther into the master cylinder bore.
5. When the brake pads are seated correctly, release the pressure from the pedal.
To learn more about pressure to the brake pedal refer :
https://brainly.com/question/8492751
#SPJ4
The Code reference that specifies the required number of receptacles in a hallway located in non-dwellings is ___. Select N/A (not applicable) if there is not a Code reference for this.
Select one:
a. 210.52(H)
b. 210.52(A)(3)
c. 210.60(B)
d. 210.70(A)(2)(a)
e. none of these
210.70(A)(2)(a) is a Code reference that specifies the required number of receptacles in a hallway located in non-dwellings. According to this Code reference, a hallway located in a non-dwelling must have at least one receptacle outlet for every 12 feet of hallway length.
This Code reference also specifies that the receptacles must be installed at least 6 feet above the floor and must be accessible. This Code reference is applicable to all hallways located in non-dwellings, including those in commercial and industrial buildings. Additionally, this Code reference specifies that the receptacles must be of the type specified in 210.70(A)(2)(b). This Code reference also specifies that the receptacles must be installed in accordance with the manufacturer's instructions and must be protected by a ground-fault circuit interrupter (GFCI). Finally, this Code reference specifies that the receptacles must be installed in a manner that prevents the use of an extension cord.
Learn more about Code reference here
https://brainly.com/question/24174389
#SPJ4
TCL Rosu TV
.
Does anyone know why my stuck is like this?
Try rebooting the router by unplugging it from the power source, then plugging it back in.
Why is my TCL Rosu TV not connecting?Unplug the router from the power supply, then connect it back in to see if that can restart it. Change the wireless security setting on the router to WPA-PSK (TKIP). Check the "Advanced Router Settings" section below by scrolling down.Ten seconds after unplugging your Android TV, plug it back in. Retry pairing it while your Android TV is on. Check to see if your device can link to other gadgets, like a tablet or phone. When connecting to other devices, your device: Restore the factory settings on your Android TV.Restarting any problematic equipment, including your smart TV, is the simplest universal step in troubleshooting. Before plugging the TV back in, wait at least 30 seconds after turning it off and unplugging it from the wall.Learn more about TV not connecting refer to :
https://brainly.com/question/30229078
#SPJ1
Clear statements of what students will achieve as a result of a lesson that they exhibit in an observable way. Also called learning outcomes.
Observable outcomes are the data sources and performance indicators, such as observations, artefacts, and dialogues, that allow for evaluation of the effectiveness of the remediation plan.
What is an example of observable learning?Both kids and adults can pick up new talents by watching others. Mom can teach a youngster how to do her nails, and films of others doing weightlifting can teach an adult how to do it.Anything you can observe another person doing is considered to be an observable activity. Walking, talking, sitting, singing, cuddling, eating, sleeping, solving math problems, and similar activities fall under this category.In order to represent what the learner will be able to perform as a result of the learning activity, learning objectives must be precise, observable, and measurable. They serve as benchmarks by which to assess advancement toward the accomplishment of the bigger objective.The value of observational learning is that it enables people, particularly youngsters, to learn new responses by observing how others behave.To learn more about Observable refer to:
https://brainly.com/question/854135
#SPJ4
suppose an uncharged solid steel ball, for example, one of the steel balls used in an old-fashioned pinball machine, is resting on a perfect insulator. some small amount of negative charge (say, a few hundred electrons) is placed at the north pole of the ball. if you could check the distribution of the charge after a few seconds, what would you detect?
After a few seconds, you would detect that the negative charge has spread out over the entire surface of the steel ball. This is because steel is a good conductor of electricity, so the charge quickly distributes itself evenly over the metal surface.
What factors would affect the charge distribution on the surface of the steel ball?The charge distribution on the surface of the steel ball would be affected by several factors. The material properties of the steel ball, such as its electrical conductivity and dielectric constant, would affect how the charge is distributed. The distance between the charged particle and the steel ball, as well as the size of the steel ball, would also be important factors. The presence of any other charged particles or electric fields in the vicinity of the steel ball would also affect the charge distribution. Finally, the shape of the steel ball would also have an effect on the charge distribution, as the charge would tend to be more concentrated at certain points than others.To learn more about charge distribution refer to:
https://brainly.com/question/16242927
#SPJ4
determine the circulation for the given vector field around the enclosed half circle of radius 1.
To determine the circulation for the given vector field around the enclosed half circle of radius 1, we need to calculate the line integral of the vector field along the boundary of the half circle.
The line integral is calculated by integrating the dot product of the vector field and the differential of the boundary. The circulation is then equal to the line integral divided by 2π. To calculate the line integral, we need to know the vector field and the boundary of the half circle. Once we have this information, we can use the equation for the line integral to calculate the circulation.
To calculate the circulation for the given vector field around the enclosed half circle of radius 1, we need to first calculate the line integral of the vector field along the boundary of the half circle. The line integral is calculated by integrating the dot product of the vector field and the differential of the boundary. The differential of the boundary is equal to the vector from the starting point to the end point of the boundary. The vector field can be expressed as a function of the coordinates of the boundary. Once we have the vector field and the differential of the boundary, we can use the equation for the line integral to calculate the circulation. The circulation is then equal to the line integral divided by 2π.
Learn more about line integral here
https://brainly.com/question/29850528
#SPJ4
1. A steel container expands in volume 1% when the pressure with in it is increased by 70Mpa. At standard pressure, it holds 8kg of water; =1000kg/m3. For K=2.05Gpa, when it is filled, how many kilograms of water must be added to increase the pressure to 70Mpa (gage)?
0.268 kg of water must be added to increase the pressure to 70 Mpa (gage).
Solving for how many kilograms of water must be added to increase the pressure to 70 Mpa (gage):To find the amount of water needed to increase the pressure to 70Mpa, we need to use the formula:
Change in volume = (Initial volume) x (Change in pressure)
Young's modulus
The initial volume of the container is 8 liters, since the container holds 8kg of water at standard pressure and the density of water is 1000 kg/m³.
So, change in volume = 8 x 10⁻³ m³
We know that the container expands by 1% when the pressure inside it is increased by 70 MPa, and we want to find the amount of water needed to increase the pressure to 70 MPa.
So, Change in pressure = 70 MPa
Young's modulus (K) = 2.05 GPa
Therefore, Change in volume = (8 x 10⁻³) x (70 / 2.05 x 10^9) = 2.68 x 10⁻⁵ m³
To find the amount of water needed to increase the pressure to 70 MPa, we need to multiply the change in volume by the density of water.
So, amount of water needed = (2.68 x 10⁻⁵) x (1000) = 0.268 kg
Therefore, 0.268 kg of water must be added to increase the pressure to 70 Mpa (gage).
Learn more about Calculations on kilograms on
https://brainly.com/question/13729893
#SPJ1
The y-component of the force F which a person exerts on the handle of the box wrench is known to be 87 lb. Determine the x-component and the magnitude of F
The force's x-component is 38.18 lb, while the force's magnitude is 93.16 Fy and the force F applied to the box wrench's handle is 86 lb.
Determine the x-component ?The force's x-component is 38.18 lb, while the force's magnitude is 93.16 Fy and the force F applied to the box wrench's handle is 86 lb.
Taking into account the triangle in Fig.
Perpendicular magnitude is equal to P = 12.
Base magnitude is B = 5.
Pythagoras's theorem is used
H = √P² + 5²
H = 13
12/13
y-component of force is given given as:
F= 86*(13/12)
F = 93.16 l b
F ( X) = 38.18 lb
To learn more about x-component refer
https://brainly.com/question/14284964
#SPJ4
according to siemens enterprise communications, what is one of the most effective routes to stealing confidential data from organizations?
Siemens Enterprise Communications, a German company, claims that social engineering is one of the most efficient ways to obtain private information from businesses.
Which of the following categories of data thieves cannot take from their intended victims? Siemens Enterprise Communications, a German company, claims that social engineering is one of the most efficient ways to obtain private information from businesses.In a recent Siemens test, engineering succeeded in fooling 85% of the office workers.To deceive people and fill up their personal information, such as bank account information, phone numbers, addresses, usernames, and passwords, etc., phishers frequently create fake websites.The most typical phishing fraud involves deceptive tactics.Fraudsters use this ruse to steal people's login information or personal information by pretending to be a reputable business.The most prevalent kind of cyberattack is called malware, which includes a wide range of subtypes such ransomware, trojans, spyware, viruses, worms, keyloggers, bots, cryptojacking, and other attacks that make use of software in a destructive way.To learn more about confidential data refer
https://brainly.com/question/29413269
#SPJ4
T/F the progress bar indicates how many concepts you have completed, how many are in progress, and how many are still left in the assignment.
The progress bar indicates how often concepts that have completed, how many still are in progress, and how many are left in the assignment, indicating that the given statement is true.
What is progress bar?The progress bar on your assignment page is an excellent way to monitor your progress.It shows how many concepts you've finished, how many are currently in progress, and how many are still outstanding. Knowing this information will assist you in planning and prioritizing your tasks, allowing you to complete the assignment on time and to the best of your ability.The assignment tracker's progress bar is a great way to keep track of your progress. It shows how many concepts you've completed, how many are in progress, and how many are still outstanding.Therefore, The progress bar displays how many concepts you have completed, how many are still being worked on, and how many are left in the assignment.To learn more about progress bar refer to :
https://brainly.com/question/30279148
#SPJ4
patient sustained a stab wound to the right neck during a domestic dispute and underwent wound exploration. the stab wound was extended, and examination of surrounding bones, connective tissue, muscles, and nerves revealed normal findings. no foreign bodies were found. the area was debrided and irrigated. coagulation of minor subcutaneous and muscular blood vessels was achieved with electrocautery. the wound was cleaned and closed with 3-0 vicryl.
To achieve wound hydration, eliminate deeper debris, and help with the visual examination, a solution is continuously pumped across an open wound surface.
When is wound irrigation used?
Wound irrigation is recommended for the management of both acute and chronic wounds, particularly those that will be sutured, repaired surgically, or debrided. Irrigation is the process of pouring a liquid solution over an open wound to better see the wound and to help clear debris from the deeper areas of the lesion. Debridement is the process of removing unhealthy or infected tissue to speed up the healing of wounds. In arid locations and during periods of below-average rainfall, irrigation aids in the growth of crops, upkeep of landscapes, and regreening of disturbed soils.
Irrigation is used for these purposes as well as to protect crops from frost, control weed growth in grain fields, and avoid soil consolidation.
To learn more about surface refer to:
https://brainly.com/question/4580651
#SPJ4
A bullet in a rifle accelerates uniformly from rest at 65 000 m/s2. If the velocity of the bullet as it leaves the muzzle is 450 m/s, (i) how long is the rifle barrel? (ii) How long did it take for the bullet to travel the length of the barrel? (iii) What is the average speed of the bullet?
The length of the rifle barrel will be about 0.69 cm. It took the bullet about 0.0069 milliseconds to travel the length of the barrel. And the average speed of the bullet is approximately 441.9 m/s.
(i) how long is the rifle barrel?
To find the length of the rifle barrel, we can use the equation:
length = (velocity^2 - initial velocity^2) / (2 * acceleration)
Plugging in the given values:
length = (450 m/s)^2 / (2 * 65 000 m/s^2) = 0.0069 m
So the length of the rifle barrel is about 0.69 cm.
(ii) How long did it take for the bullet to travel the length of the barrel?
To find the time it took for the bullet to travel the length of the barrel, we can use the equation:
time = velocity / acceleration
Plugging in the given values:
time = 450 m/s / 65 000 m/s^2 = 0.000069 s
So it took the bullet about 0.0069 milliseconds to travel the length of the barrel.
(iii) What is the average speed of the bullet?
To find the average speed of the bullet, we use the formula:
average speed = total distance / total time
Given that the bullet is accelerating uniformly, we can use the harmonic mean formula to find the average speed
average speed = 2 * length * velocity / (length + velocity/acceleration)
Plugging in the given values:
average speed = 2 * 0.0069 m * 450 m/s / (0.0069 m + 450 m/s/65000m/s^2) = 441.9 m/s
So the average speed of the bullet is approximately 441.9 m/s.
To learn more about rifle barrel, visit: https://brainly.com/question/14661669
#SPJ1
in order to generate findings about causation, researchers must use research. correlational experimental observational naturalistic
In order to generate findings about causation, researchers must use experimental research.
What is the difference between correlational and experimental research? Correlational research is a type of research that looks at the relationship between two or more variables. It seeks to identify the correlation, or relationship between the variables, without making any assumptions about cause and effect. Correlational research is used to find out if there is a relationship between two or more variables, and if so, what is the strength of the relationship. This type of research does not allow us to make conclusions about cause and effect.Experimental research is a type of research that looks for cause and effect relationships between two or more variables. It involves manipulating one variable to observe the effect on another variable. Experimental research allows researchers to make conclusions about cause and effect relationships, as it allows them to control the environment and look for changes in the dependent variable. Experiments are often used in the natural sciences, such as biology and psychology, but can also be used to study social and economic phenomena.To learn more about experimental research refer to:
https://brainly.com/question/17009178
#SPJ4
if a body is subjected to a coplanar system of loading, which internal resultant loading component is zero at the section obtained by the method of sections?
In the case of a coplanar system of loading, the internal resultant loading component at the section produced by the method of sections is zero. When cutting the piece for the coplanar loading method, there will be
What is coplanar door?
Coplanar refers to two surfaces that are installed absolutely flush with one another and signifies "put on the same plane." This is the leaf in relation to the architraves in our case, or
The MFU is a simple-to-install sliding door system that enables a door to close "flush" against the surrounding walls, giving it a neat and inconspicuous appearance and, if you so want, virtually concealing the door! No bottom track is necessary, allowing for a flooring run that is unobstructed.
Know more about method, Visit:
https://brainly.com/question/30076317
#SPJ1
With 3-phase motor drives that use SCR 6-pulse (6-diode)rectifiers, only one SCR can be on at any given timetrue or false
False. With 3-phase motor drives that use SCR 6-pulse (6-diode)rectifiers, multiple SCRs can be on at any given time. The SCRs are connected in a bridge configuration, which allows for multiple SCRs to be on at the same time.
This allows for the motor drive to be more efficient, as it can draw power from multiple sources at the same time. Additionally, this configuration allows for the motor drive to be more reliable, as it can draw power from multiple sources in the event of a failure of one of the SCRs. SCR 6-pulse (6-diode) rectifiers are a type of rectifier used in 3-phase motor drives. These rectifiers are composed of six SCRs (silicon-controlled rectifiers) connected in a bridge configuration. This configuration allows for multiple SCRs to be on at the same time, which allows for the motor drive to be more efficient and reliable. The SCRs are used to convert the alternating current (AC) power from the power source into direct current (DC) power, which is then used to power the motor.
Learn more about SCRs here
https://brainly.com/question/30287469
#SPJ4
Question 4
The removeElement method is intended to remove all instances of target from the ArrayList object data passed as a parameter. The method does not work as intended for all inputs.
public void removeElement(ArrayList data, int target)
{
for (int j = 0; j < data.size(); j++)
{
if (data.get(j).equals(target))
{
data.remove(j);
}
}
}
Assume that the ArrayList object scores and the int variable low_score have been properly declared and initialized. In which of the following cases will the method call removeElement(scores, low_score) fail to produce the intended result?
The removeElement method will fail to produce the intended result in the following cases:
If the ArrayList object scores contains more than one instance of the same value as low_score, only the first instance will be removed and the other instances will remain in the list.If the ArrayList object scores contains any elements whose type is not compatible with the type of lowscore (e.g. if lowscore is an integer and scores contains a String), the method will throw a ClassCastException.If the ArrayList object scores contains any elements that are null, the method will throw a NullPointerException.Learn more about The removeElement method:
https://brainly.com/question/14190464
#SPJ4
describe the three parts (sensor/transducer, signal conditioning, output stage) of the following measurement systems: a) measuring cup used in the kitchen b) system used to measure the gasoline pumped into a car at the gas station. if you have to look on the internet to see how these measurement devices work. if one of the three parts of a general measurement system do not exist in a) or b) then say so.
A measurement system is a system used to measure physical quantities and convert them into a form that is easier to read and interpret.
Measurement systemA) Measuring Cup Used in the Kitchen: Sensor/Transducer: A measuring cup typically has lines or markings on the inside that indicate the amount of liquid inside. This acts as the sensor/transducer because it converts the physical quantity of the liquid into a visual representation. Signal Conditioning: Not applicable.Output Stage: Not applicable.B) System Used to Measure the Gasoline Pumped into a Car at the Gas Station: Sensor/Transducer: The sensor/transducer in this system is typically a flow meter. It measures the rate of flow of the gasoline as it is pumped into the car.Signal Conditioning: The signal from the flow meter is conditioned by the gas pump computer. It filters out noise, amplifies the signal, and converts it into a signal the computer can understand.Output Stage: The output stage of this system is the display at the pump, which displays the amount of gasoline pumped and the cost.To learn more about measurement system refer to:
https://brainly.com/question/105317
#SPJ4
Measurement system, any of the systems used in the process of associating numbers with physical quantities and phenomena.
What’s the purpose of things?• A)Measuring Cup for Kitchen Use: Sensor/Transducer: A measuring cup usually contains lines or markings on the inside to show how much liquid is inside. This functions as a sensor/transducer by converting the physical quantity of liquid into a visual representation.
• B)Gasoline metered at the pump, system used at gas stations to monitor the amount of gasoline poured into an automobile. If you have to check up how these measurement equipment function on the internet.
Flow estimation
The gasoline pumped must be properly measured by the apparatus. Flow is nearly commonly measured using a four-stroke piston meter linked to an electronic encoder.
• Transducers and sensors ,A sensor and a transducer are both used to detect changes in the environment or an item to which they are attached. A sensor, on the other hand, will produce the same output format, and a transducer will turn the measurement into an electrical signal.
• Signal conditioning is a data collecting technique that is carried out with the help of a signal conditioner. This device transforms one sort of electrical or mechanical signal (input-signal) into another (output-signal).
• The fundamental goal of an operational amplifier’s output stage is to provide a given amount of signal power into a load while exhibiting acceptable levels of signal distortion.
To learn more about Measurement System to refer:
https://brainly.com/question/29379210
#SPJ4
b. draw the equivalent circuit of the alternator per phase under the dc field excitation conditions given above. c. what is the nominal full load current per phase? 2. a. if the alternator in problem 1 supplies a resistive load of 120mw at a voltage of 12kv, what must be the induced voltage eo ?
The nominal and rated currents are same. When a motor is producing its rated mechanical output at its shaft, this is the current that it is drawing.
Explain about the nominal full load current?The maximum current that a given load can drain from the circuit is known as full-load current. The nominal current is the current at which efficiency will be at its highest. However, in most real-world scenarios, these are all the same; substituting the same value for each of these will have no effect.
The electrical voltage during typical operation as provided by the manufacturer or supplier is the nominal voltage of an electrical load or a voltage source (battery, generator, power grid). It is always the voltage's RMS value unless otherwise stated.
The amount of current a motor uses to generate its rated horsepower load at its rated voltage is known as the full-load amperes (FLA). NEC tables
To learn more about nominal full load current refer to:
https://brainly.com/question/16178536
#SPJ4
The focus of these problems will be working with information extracted from a
municipal government data feed containing bids submitted for auction of property.
The data set is provided in two comma-separated files:
1. eBid_Monthly_Sales.csv (larger set of 17,937 bids)
2. eBid_Monthly_Sales_Dec_2016.csv (smaller set of 179 bids)
This assignment is designed to explore hashing algorithms by implementing a hash with chaining of collisions for bids loaded from a CSV file.
We provide a starter console program that uses a menu to enable testing of the sort logic you will complete. It also allows you to pass in the path to the bids CSV file to be loaded, enabling you to try both files. In this version the following menu is presented when the program is run:
Menu:
1. Load Bids
2. Display All Bids
3. Find Bid
4. Remove Bid
9. Exit
One form of completely automated advertising is smart display campaigns. Remember that your desired ROAS may have an impact on the umber of conversions you receive.
Target CPA bidding is a Smart Bidding technique that automatically sets bids to increase conversions (customer actions). You specify an average cost for each conversion when creating the Target CPA (target cost-per-action) bid strategy. The average conversion value (such as revenue) that you would hope to receive for each dollar spent on us known as the target ROAS. Remember that your desired ROAS may have an impact on the umber of conversions you receive. For instance, if you set your objective too high, fewer individuals may see your advertisements. If Paul has confidence in his capacity to create bids on his own, he can rely on the Smart Display campaign.
Learn more about Target ROAS here:
https://brainly.com/question/29697386
#SPJ4
Select below the name of the processor created by Intel for use in low-end desktops, netbooks, and laptops.
Intel Atom. Intel Atom is a processor created by Intel for use in low-end desktops, netbooks, and laptops. It is designed to be energy efficient and cost-effective, while still providing good performance.
It is typically used in devices such as netbooks, tablets, and other small form factor devices. It is also used in some embedded systems and industrial applications. Low-end desktops, netbooks, and laptops are computers that are designed to be affordable and have lower performance than more expensive models. They typically have slower processors, less RAM, and fewer features than more expensive models. They are often used for basic tasks such as web browsing, word processing, and other everyday tasks. A processor is a type of computer chip that is responsible for executing instructions and performing calculations. It is the main component of a computer and is responsible for carrying out the instructions of a computer program.
Learn more about Intel Atom here
https://brainly.com/question/29780027
#SPJ4
p1 - connecting computing consider the following program, which is intended to display the number of times a number target appears in a list.
The program correctly displays the number of times target appears in the list. The program correctly keeps track of the number of times that the target appears in the list and displays this number.
What is the purpose of the code?The purpose of this code is to count the number of times a specified target appears in a given list. The code begins by setting the initial count to 1. This is followed by a "For Each" loop, which iterates over each element of the list. For each element, the code checks if it is equal to the target. If so, the count is incremented by 1. After the loop finishes, the code displays the count, which is the number of times the target appears in the list. This code can be used to quickly determine the frequency of a particular number or value in a list, making it easier to analyze and visualize the data.To learn more about purpose of code refer to:
https://brainly.com/question/30032849
#SPJ4
neglecting the size of the ball, determine the magnitude va of the basketball's initial velocity. (figure 1) express your answer to three significant figures and include the appropriate units.
The trajectory displayed is followed by a basketball as it is thrown at an initial speed of 8.5 m/s.
Explain about the initial velocity?Any object will accelerate as a result of forces acting on it. This acceleration causes a change in the object's velocity. The object's initial velocity is hence its speed prior to the change brought on by acceleration.
The time required is 3 seconds if the terminal velocity of the person is 10 meters per second and the acceleration is 2 meters per second. How fast did that person start moving? u= 10+6 = 16m/s.
When gravitational force is first exerted on an item, its initial velocity indicates how quickly it moves. The final velocity, on the other hand, is a vector number that gauges the speed and direction of a moving object after it has experienced its maximum acceleration.
To learn more about initial velocity refer to:
https://brainly.com/question/24493758
#SPJ4
to practice problem-solving strategy 15.1 mechanical waves. waves on a string are described by the following general equation y(x,t)
The transverse displacement will be 0.089963 m. The velocity of the shear wave particles is orthogonal to the direction of the wave.
What is transverse displacement?
Here given the data
Then the equation y(x,t)=Acos(kx−ωt)
speed (v) = 9.00 m/s
amplitude (A) = 9.00 × 10^−2 m
wavelength (λ ) = 0.480 m
We have to find out transverse displacement.
Here we know that.
v = angular frequency / wave number
also wave number = 2 / λ
= 2 / 0.480
= 13.0899
angular frequency = v x k
angular frequency = 9.00 × 13.0899
angular frequency = 117.8097 rad/sec
= 118 rad/sec
Therefore, the equation y(x,t)=Acos(kx−ωt)
y(x,t)=9.00 × 10^−2 cos(13.0899 x−118t)
If x =0 and and t = 0
Then, maximum y(x,t)= 9.00 × 10^−2 cos(13.0899 (0) − 118 (0))
= 9.00 × 10^−2 m
if x = 1.59 m and t = 0.150 s
Then,
y(x,t) = 9.00 × 10^−2 cos(13.0899 (1.59) −118(0.150) )
y(x,t) = 9.00 × 10^−2 × (0.99959)
y(x,t) = 0.089963 m
Therefore the transverse displacement is 0.089963 m
The complete question:
" To practice Problem-Solving Strategy 15.1 Mechanical Waves. Waves on a string are described by the following general equation y(x,t)=Acos(kx−ωt). A transverse wave on a string is traveling in the +x direction with a wave speed of 9.00 m/s , an amplitude of 9.00×10−2 m , and a wavelength of 0.480 m . At time t=0, the x=0 end of the string has its maximum upward displacement. Find the transverse displacement y of a particle at x = 1.59 m and t = 0.150 s ."
To learn more about transverse displacement refer to :
brainly.com/question/28200873
#SPJ4
// quartstogallons.java class quartstogallons { public static void main(string[] args) { // write your code here } }
The alternative that can be utilized to change the /* missing code */ in order for the statement to compile correctly is.
List of years, The Java programming language is the subject of this query. As can be seen from the query, an ArrayList is involved. In Java, the syntax to declare an ArrayList with no specific data type is as follows: ArrayList [Name of the Lists] = new ArrayList(); The list name is now "years" in the query. Thus; The appropriate statement to replace any missing code in order to avoid mistakes is; ArrayList years is a replacement option that can be used to fill in any missing code, ensuring that the statement compiles successfully. Simply put, resizable arrays are ArrayLists. The statements (b) new ArrayList() and (c) I and III only are capable of substituting for the missing code, respectively. ArrayList creation syntax is as follows: new ArrayListType>() using the argument ArrayListType> str;
Learn more about ArrayList here:
https://brainly.com/question/29309602
#SPJ4
if a twisted-pair cable has a diameter of 0.8 cm, which of the following options would you apply as the bend radius of the cable so that data transmission is not impaired?
The minimum bend radius for a twisted-pair cable with a diameter of 0.8 cm should be at least 3.2 cm. This ensures that the cable is not bent too sharply, which could impair data transmission.
When a twisted-pair cable is bent too sharply, the individual wires within the cable can be stretched or compressed, which can cause signal interference and impair data transmission. To prevent this, the bend radius of the cable should be at least four times the diameter of the cable. This ensures that the cable is not bent too sharply, which can cause signal interference and impair data transmission. For a twisted-pair cable with a diameter of 0.8 cm, the minimum bend radius should be at least 3.2 cm. This ensures that the cable is not bent too sharply, which can cause signal interference and impair data transmission.
Learn more about twisted-pair cable here
https://brainly.com/question/25337328
#SPJ4
Your biology test is in a few days, and you have to study a large amount of material in order to prepare for it. Define all of the following concepts and explain how each could apply to your situation.a. Declarative memoryb. Semantic memoryc. Mnemonic devicesd. Short-term (working) memory
Short-term memory briefly refers to the record while declarative memory bases itself on names, places, etc., semantic memory bases itself on grammar, and so forth.
The definition of declarative memory?Declarative memory is a sort of memory that is dependent on a particular piece of information, such a name, a certain date, etc.Short-term memory can be described as the memory that maintains information for a brief amount of time, whereas semantic memory is based on the syntactical and grammatical characteristics of a text.In summary, declarative memory refers to names, places, etc., semantic memory refers to grammar, and short-term memory refers to the information for a brief period of time.Short-term memory briefly refers to the record while declarative memory bases itself on names, places, etc., semantic memory bases itself on grammar, and so forth.To learn more about Declarative memory refer to:
brainly.com/question/6652786
#SPJ4
Need help to answer.
ASAP.
A furnace wall consists of 125 mm wide refractory brick and 125 mm wide insulating firebrick separated by an air gap. The outside wall is covered with a 12 mm thickness of plaster. The inner surface of the wall is at 11000C and the room temperature is 250C. The heat transfer coefficient from the outside wall surface to the air in the room is 17 W/m2K, and the resistant to heat flow of the air gap is 0. 16K/W. The thermal conductivities of refractory brick, insulating firebrick, and the plaster are 1. 6, 0. 3, and 0. 14 W/mK respectively. Calculate:
(i) the rate of heat loss per unit area of wall surface;
(ii) the temperature at each interface throughout the wall;
(iii) the temperature at the outside surface of the wall.
The temperature at the outside surface of the wall is 1344 0.8 watts.
What is the temperature at the outside surface of the wall?Determine the loss rate per square foot of the wall surface. Our refractor block brick's thermal resistance is equal to B divided by K. A times one. Thus, this is equal to 1.6 times one divided by 12.5 times 10 to the negative three. Our air gap contributes 0.16 K per W to our thermal resistance. We have three fire bricks as a result. Three divided by K gives us B. A thrice. This equals 0.3 times one divided by 1 25 times 10 to the negative three. Because of our plaster, four equals four divided by B divided by K.Four times our area is equal to 12 x 10 3 / 30.14 x 1 or 4 times our area. Furthermore, our thermal resistance is not equal to one divided by H but rather by A due to the heat transfer from the outside. This makes 1/7. The reason why adding R. One plus R. A plus R. three plus our four plus are ineffective is because of our total net thermal resistance. We thus obtain 0.799 K per W. The rate of heat loss throughout our entire surface area, Q, is equal to T. W minus T. Zero divided by R, or 111 100 minus 25 divided by 0.799, which is 1344 0.8 watts.To learn more about loss rate refer to:
https://brainly.com/question/16556041
#SPJ4
Direct-tension tests use what kind of test
specimens? Select all that apply.
A. Cross-tension specimens
B. Longitudinal fillet weld specimens
C. U-shaped specimens
D. Round tensile specimens
Direct-tension tests use the kind of test specimens known as D. Round tensile specimens
What is a Direct-tension test?A direct-tension test, also known as a tension test or a tensile test, is a type of mechanical test used to determine the material's strength and behavior under tension loads.
The test specimen is typically a cylindrical or round shape and is placed in a tensile testing machine. The machine applies a load to the specimen in one direction, stretching it until it fractures.
The load, elongation, and other data are recorded during the test, and from these data, the material's properties such as ultimate tensile strength (UTS), yield strength, and modulus of elasticity can be determined.
Read more about Direct-tension tests here:
https://brainly.com/question/29843307
#SPJ1
if a furnace is using 1280 lbs./hr of oxygen, what is the correct balance equation and how much pentane will completely combustion?
The balance equation for pentane, C5H12's complete combustion is 5CO2 (g) + 6H2O = C5H12 (l) + 8 O2 (g) (g).
First, we should comprehend how hydrocarbons burn. A hydrocarbon, or molecule made up only of carbon and hydrogen atoms, is pentane, C5H12. When talking about the combustion of hydrocarbons, the two by products that are typically predicted are CO2 and 6H2O. Keeping in mind that "reaction with O2" refers to combustion, we may create the equation shown below: O2 (g) + C5H12 (l) + CO2 (g) + H2O (g), Therefore, we may determine the equation's balance by counting the number of atoms in each side of the equation. 5 C atoms, 12 H atoms, and 2 O atoms are on the right side. Left: one C atom, two H atoms, and three O atoms. By dividing CO2 by 5, we can begin to establish a balance: O2 (g) + C5H12 (l) = 5CO2 (g) + H2O (g).
Learn more about Combustion here:
https://brainly.com/question/29847993
#SPJ4
A large rock became visible to a driver at a distance of 175 ft. Assuming a perception-reaction time of 0. 8 s, an initial speed of 42 mi/h, a coefficient of friction of 0. 5, and a level roadway, calculate the speed at impact
Answer:
Assuming a perception-reaction time of 0.8 s, an initial speed of 42 mi/h, a coefficient of friction of 0.5, and a level roadway, calculate the speed at impact.
Explanation: