A single phase inductive load draws 10 MW at 0.6 power factor lagging. Draw the power triangle and determine the reactive power of a capacitor to be connected in parallel with the load to raise the power factor to 0.85.

Answer:

what do you mean by that ? snap points ?

Answer:

D. Both pull-in and hold-in windings are energized.

Explanation:

The instant the ignition switch is turned to the start position, "Both pull-in and hold-in windings are energized." This is because the moment the ignition switch is turned to the start position, voltage passes through to the S terminal of the solenoid.

The hold-in winding is attached to the case of the solenoid. Similarly, the pull-in winding is also attached to the starter motor. Thereby, the current will move across both windings by getting energized to generate a strong magnetic field.

Answer: 98.5% of pearlite was formed during the equilibrium cooling

Explanation:

First we calculate the fraction of pro-eutectoid phase which forms for equilibrium cooling of the 1085 steel from 1000°C at room temperature;

we know that in 1085 steel, last two digits denotes the carbon percentage

so 1085 steel contains 0.85% carbon.

Now from the diagram, carbon percentage is greater than the eutectoid com[psition

i.e 0.85 > 0.76

it is a hyper eutectoid steel

so

fraction of pro eutectoid phase W_Fe₃C = (0.85 - 0.76) / ( 6.7 - 0.76)

= 0.09 / 5.94 = 0.015 = 1.5%

Now, the amount of pearlite formed during the equilibrium cooling of the 1055 steel from 1000°C to room temperature will be;

pearlite (C') = (1 - W_Fe₃C)

= 1 - 0.015

= 0.985 = 98.5%

Therefore 98.5% of pearlite was formed during the equilibrium cooling

Answer:

C/C++

Explanation:

C/C++

Answer:

a)  ( ∝ ) = 69.6548

b) supply power factor = 0.6709

  displacement power factor = 0.8208

Explanation:

Given data:

Nominal voltage ( E ) = 200-V

resistance (r) = 10 milliohms

constant current ( I )  = 20 amps

Phase ; 3-phase

semi-converter  with 220-v ( line-to-line ) ,  220√2  ( phase voltage )

frequency ; 60 Hz

a) determine the firing angle of thyristors

Vo = E + I*r

    = 200 + 20*10*10^-3

    = 200.2 v

attached below is the remaining part of the solution

firing angle of thyristors for charging process ( ∝ ) = 69.6548

b) determine displacement power factor and supply power factor

attached below is the detailed solution

Displacement power factor ( Dpf ) = cos ( ∝ /2 ) = 0.8208

displacement power factor = g * Dpf

                                             = 0.81747 * 0.8208 = 0.6709

Answer:

The answer is "[tex]\bold{W_{in} = 645.434573 \ Btu}[/tex]".

Explanation:

Its air enthalpy is obtained only at a given temperature by A-17E.  

The solution from the carbon cycle is acquired:

[tex]\to \Delta U= W_{in}-m_{out}h_{out}=0\\\\\to W_{in} = (m_1 - m_2)h[/tex]

           [tex]=\frac{Vh}{RT}(P_1- P_2)\\\\= \frac{40 \times 138.66}{0.3704\times 580}(50-25) Btu\\\\= \frac{5,546.4}{214.832}(25) Btu\\\\= 25.8173829(25) Btu\\\\ =645.434573 Btu[/tex]

[tex]W_{in} = 645.434573 \ Btu[/tex]

Answer:

the motor input power is 19.42 KW

the Reactive power is 17.65 KVAR

Current is 31.56 A

Explanation:

Given that;

V = 480V

h.p = 25 hp

p.f = 0.74 lagging

n_motor = 96%

so output = 25hp

and we know that;

1hp = 746 watt

watt = hp × 1hp

so output in watt = 25 × 746 = 18650 Watt = 18.65 KW

n_motor = (output / input) × 100

96 = 1865 / Input

96Input = 1865

Input = 1865 / 96

Input = 19.42 KW

Therefore the motor input power is 19.42 KW

P = √( 3 × V × I × cos∅)

19.42 = √( 3 ×480 × I × 0.74)

I = 31.56 A

Therefore Current is 31.56 A

Q = √( 3 × V × I × sin∅)

we know that

cos∅ = 0.74

so ∅ = cos⁻¹(0.74) = 42.26

so we substitute

Q = √( 3 × 480 × 31.56 × sin(42.26))

 = 17.65 KVAR

Therefore the Reactive power is 17.65 KVAR

Answer: hydraulic retention time,τ=28.67 hours

Explanation:

The hydraulic retention time  τ (tau),  is given as  The volume of the settling tank(V) divided by the influent flowrate(Q)

τ =V/Q

But Volume is not known  and is given as

Volume =  surface area  x depth of the tank

= 8000 ft² X 12 ft

= 96,000 ft³

Also, the influent flow rate is in mgd ( million gallons per day), we change  it to  ft³/sec so as to be in same unit with the volume in ft³

1 million gallons/day = 1.5472286365101 cubic feet/second

0.6mgd =  1.5472286365101 cubic feet/second  x 0.6

=0.93cubic feet/second

τ =V/Q

96,000 ft³/0.93 ft³/sec

τ=103,225.8 secs

changing to hours

103,225.8 /3600 =28.67 hours

The hydraulic retention time =28.67 hours

Answer:Decay rate constant,k  = 0.00376/hr

Explanation:

IsT Order  Rate of reaction is given as

In At/ Ao = -Kt

where [A]t is the final concentration at time  t  and  [A]o  is the inital concentration at time 0, and  k  is the first-order rate constant.

Initial concentration = 80 mg/L

Final concentration = 50 mg/L

Velocity = 40 m/hr

Distance= 5000 m

Time taken = Distance / Time

              5000m / 40m/hr = 125 hr

In At/ Ao = -Kt

In 50/80 = -Kt

-0.47 = -kt

- K= -0.47 / 125

k = 0.00376

Decay rate constant,k  = 0.00376/hr

Answer:

b

Explanation:

Answer:

155 KJ

Explanation:

The total enthalpy is given by

ΔH=ΔU + PV

Where;

ΔH = enthalpy

ΔU = internal energy = 25000 kJ/kg/ 5 kg = 5000 KJ

P = 150 kPa = 150,000 Pa

V =  1 m3

ΔH=  5000 + (150,000 * 1)

ΔH=  155 KJ

Answer:

406.140 KHz

Explanation:

Given data:

Rsig = 100 kΩ

Rin = 100kΩ

Cgs = 1 pF,

Cgd = 0.2 pF,  and   etc.

Determine the expected 3-dB cutoff frequency

first find the CM miller capacitance

CM = ( 1 + gm*ro || RL )( Cgd )

     = ( 1 + 5*10^-3 * 25 || 20 ) ( 0.2 )

     = ( 11.311 ) pF

now we apply open time constant method to determine the cutoff frequency

Th = 1 / Fh

hence : Fh = 1 / Th = [tex]\frac{1}{(Rsig +Rin) (Cm + Cgs )}[/tex]

                               = [tex]\frac{1}{( 200*10^3 ) ( 12.311 * 10^{-12} )}[/tex] =  406.140 KHz

Answer:

yes it is very hard you should find a reccomended doctor to aid in your situation. But in the meantime how about you give me that lil brainliest thingy :p

Answer:

Super critical

1.2 m

Explanation:

Q = Flow rate = [tex]12\ \text{m}^3/\text{s}[/tex]

w = Width = 3 m

d = Depth = 90 cm = 0.9 m

A = Area = wd

v = Velocity

g = Acceleration due to gravity = [tex]9.81\ \text{m/s}^2[/tex]

[tex]Q=Av\\\Rightarrow v=\dfrac{Q}{wd}\\\Rightarrow v=\dfrac{12}{3\times 0.9}\\\Rightarrow v=4.44\ \text{m/s}[/tex]

Froude number is given by

[tex]Fr=\dfrac{v}{\sqrt{gd}}\\\Rightarrow Fr=\dfrac{4.44}{\sqrt{9.81\times 0.9}}\\\Rightarrow F_r=1.5[/tex]

Since [tex]F_r>1[/tex] the flow is super critical.

Flow is critical when [tex]Fr=1[/tex]

Depth is given by

[tex]d=(\dfrac{Q^2}{gw^2})^{\dfrac{1}{3}}\\\Rightarrow d=(\dfrac{12^2}{9.81\times 3^2})^{\dfrac{1}{3}}\\\Rightarrow d=1.2\ \text{m}[/tex]

The depth of the channel will be 1.2 m for critical flow.

Explanation:

D. B. C. A. E. Is this a good idea

Answer:

0.2

Explanation:

Since the span and chord of the rectangular wing is missing, due to it being from the other question, permit me to improvise, or assume them. While you go ahead and substitute the ones from your question to it, as it's both basically the same method.

Let the span of the rectangular wing be 0.225 m

Let the chord of the rectangular wing be 0.045 m.

Then, the area of any rectangular chord is

A = chord * span

A = 0.045 * 0.225

A = 0.010 m²

And using the weight of the glider given to us from the question, we can find the LER for the wing.

LER = Area / weight.

LER = 0.010 / 0.05

LER = 0.2.

Therefore, using the values of the rectangular wing I adopted, and the weight of the glider given, we can see that the LER of the glider is 0.2

Please mark brainliest...

Answer: 0.2025

Explanation: I got it correct

Answer:Total Voltage = 14V

Explanation: it is possible that a circuit  can contain more than one source of electromotive force which can cause flow of current in the same or opposite direction . When the  connection to  voltage sources  allows for current  from the voltage sources to flow in  same direction,it is termed  Series aiding  Thus, the  Total/effective voltage in a series aiding circuit is  computed as the sum of series aiding voltages .

 Here we have the series aiding voltages to be 5V and 9V ,

therefore,

Total Voltage = 5V + 9V

= 14V

Answer:

Irreversibility = 5.361 kW

Explanation:

From the given information:

By applying ideal gas equation at entry:

PV =  mRT

600 × 0.3 = m × 0.287 × 300      (where R = 0.287 kJ/kg)

180 = m × 86.1

m = 180/86.1

m = 2.0905 kg/min

At the hot end, using the same ideal gas equation:

PV = mRT

100 × V = 1.4905 × 0.287 × 325

V = 139.026/100

V = 1.3903 m³/ min

This implies that: The total entropy change = Entropy of the universe

So,

[tex]m\bigg [ c_p \ In \dfrac{T_2}{T_o}-R \ In \dfrac{P_2}{P_o} \bigg] + m_2 \bigg [ c_p \ In \dfrac{T_2}{T_o}- R \ In\dfrac{P_2}{P_o} \bigg][/tex]

[tex]= 0.6\bigg [ 1.004 \ In \dfrac{245}{300}-0.287 \ In \dfrac{100}{600} \bigg] +1.4905\bigg [1.004 \ In \dfrac{325}{300}- 0.287\ In\dfrac{100}{600} \bigg][/tex]

= 0.6[-0.2033 + 0.5142] + 1.4905 [0.08036 + 0.5142]

= 1.0727 kJ/min.K

= 0.01787 kw/K

Irreversibility = [tex]T_o [ \Delta S][/tex]

Irreversibility = 300 × 0.01787

Irreversibility = 5.361 kW

Answer:

Following are the solution to this question:

Explanation:

To copy 3.0 bits in 50 dollars or run at 50 dollars, it takes just 3.0 bits as well as other bits but masks, and 50 dollars.  

Instead of shifting the $ 50 by 3 bits to 6...3 bits of [tex]\$ \ 50, \$ \ 50,0*0000 0003,[/tex] This procedure instead took place at $53 and $50  

AND [tex]\$ \ 50,\$ \ 50,0*0000 000f[/tex], take 3..0  bits

SLL [tex]\$ \ 50, \$ \ 50,0*0000 0003,[/tex]Shifts the bits to 6..3

O R [tex]\$ \ 53,\$ \ 53,\$ \ 50 ,[/tex] coping to [tex]\$ \ 53[/tex]

Answer: the air flow rate a is 90 kg/sec; Option b) 90 kg/sec is the correct answer

Explanation:

Given that;

product of combustor flow rate m = 100 kg/s

air-fuel = 9

Airflow rate = ?

⇒We know that in the combustor, air fuel are mixed and then ignited,

⇒air fuel products are exited at the combustor

let air and fuel be a and b respectively

⇒ a + b = 100 kg/sec ----- let this be equation 1

now

⇒ air / fuel = 9

a / b = 9

a = 9b -----------let this be equation 2

now input a = 9b in equation 1

9b + b = 100 kg/sec

10b = 100 kg/sec

b = 10 kg/sec

we know that

a = 9b

so a = 9 × 10 = 90 kg/sec

Therefore the air flow rate a is 90 kg/sec

Answer: Option D) 298 g/mol  is the correct answer

Explanation:

Given that;

Mass of sample m = 13.7 g

pressure P = 2.01 atm

Volume V = 0.750 L

Temperature T = 399 K

Now taking a look at the ideal gas equation

PV = nRT

we solve for n

n = PV/RT

now we substitute

n = (2.01 atm x 0.750 L) / (0.0821 L-atm/mol-K x 399 K )

= 1.5075 / 32.7579

= 0.04601 mol

we know that

molar mass of the compound = mass / moles

so

Molar Mass = 13.7 g / 0.04601 mol

= 297.7 g/mol  ≈ 298 g/mol

Therefore Option D) 298 g/mol  is the correct answer

Answer:

There are several similarities between the nucleus and a liquid droplet.

Explanation:

A droplet of liquid simply is is very small or tiny drop of liquid. It is also considered as a tiny column of liquid that is surrounded by surfaces that have zero shear stress.

A nucleus on the other hand is an assembly between protons and neutrons. The latter is electrically charged whilst the former is positively charged. The number of protons present in an element is very crucial to the qualities of an element.

The main similarities between a nucleus and a liquid droplet are:

1. a nucleus consists of a large amount of neutrons and protons in the same volume as would a liquid which contains large numbers of molecules in the same volume;

2. both the nucleus and the droplet are similar for their homogeneity in electric charge and density;

3. the molecules exert the same amount for forces towards one another as would the nuclear forces in the nucleons.

4. both of them cannot be compressed

5. both molecules and nucleus are can be subject to nuclear fission which simply mean the breaking apart into smaller units (in the case of the nucleus) or the breaking apart into smaller droplets in the case of the liquid molecule.

6. There are two types of phenomena which occurs in both the liquid droplet and the nucleus which are similar to one another. They are:

Evaporation (in the case of the liquid molecule) and reaction emission (in the case of the nucleus). In evaporation, particles are lost, in Atomic transmutation, particles are lost as well.

B)  the forces which determine the stability of droplets are surface tension and gravitation. The smaller the area, the stronger the surface tension available to keep the drops from going out of shape.

Cheers

Answer:people tend to do this when they are in a different environment they lose something or just have something going on in their life

Explanation:

Answer:

-0.1006Kw/K

Explanation:

The rate of entropy change in the air can be reduced from the heat transfer and the air temperature. Hence,

ΔS = Q/T

Where T is the constant absolute temperature of the system and Q is the heat transfer for the internally reversible process.

S(air) = - Q/T(air) .......1

Where S.air =

Q = 30-kW

T.air = 298k

Substitute the values into equation 1

S(air) = - 30/298

= -0.1006Kw/K