a force pair is created when you push on a large crate that rests on the floor. the crate does not move when pushed. which free-body diagram correctly represents the forces acting on the crate?

The height of a water-filled manometer required to measure blood pressure as high as 300 mm Hg is 229.69 cm.

A manometer is a pressure measurement device that is utilized to measure the pressure of gases and liquids in a container.

The weight of the liquid in the manometer rises or falls depending on the pressure of the gases and liquids in the container.

In order to measure blood pressure, a water-filled manometer is used. The density of blood is 1.05 x 103 kg/m3. The height of the manometer is required to be found.

The pressure of blood is 300 mm Hg.

The following formula will be used to calculate the height of the manometer:

h = (P*d)/(g*H2O)

where, P = 300 mm Hg,

d = 1.05 × 103 kg/m^3,

g = 9.8 m/s2, and

H2O = 1000 kg/m^3

Substituting the values in the equation:

h = (300*1.05*103)/(9.8*1000)

h = 229.69 cm

The height of the manometer must be 229.69 cm to measure blood pressure as high as 300 mm Hg.

Learn more about manometer: https://brainly.com/question/15191441

#SPJ11

In Part A, the angular momentum of the system about the origin can be calculated using the formula:

L = r × p, where r is the position vector from the origin to the center of mass of the system, and p is the linear momentum of the system. In this case, since the system is rotating in the xy-plane about the origin, the angular momentum is in the +z direction. The position vector r is perpendicular to the plane of rotation and has a magnitude of ℓ/2. The linear momentum of each particle is mvi, where vi is the speed of the particle. Using this information, we can calculate the angular momentum of the system as: L = (ℓ/2) × (m1v1 - m2v2). Substituting the given values, we get: L = (1/2) × (4.00 kg × 6.40 m/s - 3.00 kg × 6.40 m/s) = 22.4 kg·m^2/s. In Part B, we need to find the new angular momentum of the system if each of the masses were instead a solid sphere 10.5 cm in diameter. In this case, we can assume that the spheres rotate about their own center of mass. The moment of inertia of each sphere can be calculated using the formula for the moment of inertia of a solid sphere: I = (2/5) × mr^2, where m is the mass of the sphere and r is the radius of the sphere. Substituting the given values, we get: I = (2/5) × (m/4π) × (10.5/200)^2, where m = 4.00 kg for one sphere and m = 3.00 kg for the other sphere. The total moment of inertia of the system can be found by adding the moments of inertia of the two spheres. We can then use the formula for the angular momentum of a rotating object: L = Iω, where ω is the angular velocity of the system. However, we do not have enough information to find the angular velocity ω. Therefore, we cannot find the new angular momentum of the system with the given information.

To learn more about angular momentum click the link below

brainly.com/question/29897173

#SPJ4

(I) The Ka of HXO2 is greater than the Ka of HYO2 because the HX bond is weaker than the H-Y bond. This is because X is more electronegative than Y, which means the electron density in the H-X bond is more attracted to X, making the bond weaker than the H-Y bond. The best explaination is option (C).

(II) The Ka of HX is less than the Ka of HY because the H-X bond is longer than the H-Y bond. This is because X is more electronegative than Y, which means that the electron density in the H-X bond is more attracted to X, causing it to be longer than the H-Y bond.

Know more about electron density here:

https://brainly.com/question/15120499

#SPJ11

The change in mechanical energy of a system consisting of the heavier bucket and the earth is the sum of the potential energy of the bucket, minus the potential energy of the earth, which is the same as the weight of the heavier bucket multiplied by the distance the bucket fell.

The change in mechanical energy is the external work provided to the system. The potential energy of the bucket decreases. The work done by the earth is (weight of the heavier bucket x distance the bucket fell).

The tension in the rope is equal to the weight of the heavier bucket.

Therefore, the ordered pair of the change in mechanical energy and tension in the rope is (weight of the heavier bucket x distance the bucket fell, weight of the heavier bucket).

To learn more about mechanical energy refer to: brainly.com/question/28980000

#SPJ11

The driver should be at least 39 meters behind the vehicle in front at 30mph. Rounded to 2 significant figures, this is 39 meters.

Meters are a unit of length used in the International System of Units (SI) to measure distance or displacement. A meter is defined as the length of the path traveled by light in a vacuum during a time interval of 1/299,792,458 of a second. This definition provides a precise and universal standard for the measurement of length, as the speed of light is constant and independent of the observer.

Meters are commonly used to measure the length or width of objects, as well as the distance between two points. They are also used in scientific fields such as physics, where they are used to measure quantities such as wavelength and amplitude.

To learn more about Meter visit here:

brainly.com/question/4420812  

#SPJ4

A pail of water is swung in a vertical circle using a uniform circular motion. In order to make sure that the water doesn't spill out when the pail is upside down, a minimum constant tangential speed of 2.1 m/s is required.

The minimum constant tangential speed required by the pail of water in order to ensure that the water doesn't spill out when the pail is upside down can be calculated using the formula:

[tex]v = \sqrt{gr}[/tex]

where v = minimum constant tangential speed g = acceleration due to gravity r = radius of the circle.

The distance from the bottom of the pail to Sarah's shoulder is 0.449 m long.

Since this distance is the radius of the circular path, we can substitute it in the formula.

Therefore,

[tex]v = \sqrt{9.8 m/s^2 \times 0.449 \ m} = \sqrt{4.4102 m^2/s^2} = 2.1 \ m/s[/tex]

Therefore, the minimum constant tangential speed required by the pail of water is approximately 2.1 m/s.

Learn more about tangential speed:

https://brainly.com/question/6104448

#SPJ11

Your friend is correct. In order to determine the speed at which the person who leaves point B must walk, you need to know the length of AC and BC.

This is because the time it takes for each person to reach point C is dependent on the distance they must travel and the speed at which they are traveling.

Using the formula time = distance / speed, you can calculate the time it takes for each person to reach point C.

For the person leaving point A, the time it takes to reach point C is tA = AC / 3, since they are traveling at a speed of 3 miles per hour.

For the person leaving point B, the time it takes to reach point C is tB = BC / x, where x is the speed at which they are traveling.

Since both people are intended to reach point C at the same time, you can set the two equations equal to each other:

AC / 3 = BC / x

Cross-multiplying and solving for x gives you the speed at which the person leaving point B must walk:

x = 3BC / AC

Without knowing the length of AC and BC, you cannot determine the speed at which the person leaving point B must walk. Therefore, your friend is correct.

To know more about speed, refer here:

https://brainly.com/question/18622418#

#SPJ11

The amplitude of wave is 2.0 cm and the frequency is 4.0 Hz, then the correct statements are : B) The distance between P and R is 6.0 cm ; D)Particles at P and R are in the phase.

Moving wave whose oscillations are perpendicular to the direction of the wave is known as transverse wave.

As we know, v = fλ

v is the velocity of wave, f is frequency, and λ is wavelength.

λ = v/f

λ = 24 cm s−1 / 4.0 Hz = 6.0 cm

So the wavelength of the wave is 6.0 cm.

A.)The phase difference between particles at P and S is π/2 radians.

This statement cannot be determined from given information.

B.)Distance between P and R is 6.0 cm.

This statement is correct as the distance between two consecutive points on a wave with wavelength of 6.0 cm is also 6.0 cm.

C.)The particle velocity at Q is maximum.

This statement cannot be determined from given information.

D.)Particle at P and R are in phase.

This statement is correct as particles at two points on a wave with wavelength of 6.0 cm are in phase.

Therefore, correct statements are B and D.

To know more about transverse wave, refer

https://brainly.com/question/12584334

#SPJ1

Answer:

10.17 m/s in the direction the compact car was going (+)

Explanation:

Law of conservation of momentum states that total P before the collision must equal total momentum after the collision.

P = mv

solve for v, velocity of the two cars stuck together after the collision:

(187kg)(-38 m/s) + (702kg)(23 m/s) = (187 + 702 kg)v

         momentum before               =   momentum after

-7106 kg·m/s + 16146 kg·m/s = 889 kg(v)

9040 kg·m/s = 889 kg(v)

v = 9040 kg·m/s / 889 kg = 10.17 m/s

A hair dryer uses the electricity from the power source to run its motor and heating element when it is hooked into an electrical outlet. Heat and kinetic energy are created from this electrical energy.

One of the most frequent causes of circuit breakers being tripped by a hairdryer is an overloaded circuit. A circuit overload occurs when there are several high-powered gadgets drawing 15 to 20 amps of electricity simultaneously on the same circuit.

A conventional in-room, wall-mounted hair dryer uses roughly 1.6 kW of power on average. This indicates that a guest will use 0.4 kilowatt-hours (kWh) of power if they use their hair dryer for 15 minutes.

To know more about electricity visit:-

https://brainly.com/question/8971780

#SPJ1

Digital data can be encoded by a computer program and are easy to change by a computer program. Therefore, options A and D are correct.

A and D are two reasons why digital storage of data is more secure than analogue storage.

A - Digital data can be encoded using various encryption techniques that make it more difficult for unauthorized individuals to access or interpret the data.

D - Digital data are easy to change or modify using a computer program, but this can also be a security advantage as it allows for quick updates and corrections to be made, and changes can be tracked and logged for security purposes.

B and C are not necessarily unique to digital storage, and may also be applicable to analogue storage. Fingerprint or facial ID can be used to protect physical storage devices, and a strong password can also be used to secure both digital and analogue storage.

To find out more about digital storage, visit:

https://brainly.com/question/13150495

#SPJ1

Answer:

A. Digital data can be encoded by a computer program.

B. Digital data can be protected by a fingerprint or facial ID.

Explanation:

did quiz

The function of a rheostat is to vary the resistance in an electrical circuit, thereby controlling the amount of current flowing through the circuit.

A rheostat is an electrical instrument that is used to vary the resistance in a circuit. It is a variable resistor that can be adjusted to control the amount of current flowing through the circuit. By increasing or decreasing the resistance, a rheostat can regulate the current flow, which can be useful in various applications.

For example, in a lighting circuit, a rheostat can be used to control the brightness of a bulb by adjusting the amount of current flowing through it. Similarly, in a motor control circuit, a rheostat can be used to adjust the speed of a motor by regulating the amount of current that flows through it. Overall, the function of a rheostat is to provide variable resistance in a circuit, allowing for the control of current flow and the regulation of various electrical devices.

To know more about Rheostat, here

brainly.com/question/30649442

#SPJ4

The electric field strength between the two parallel charged plates is 514.29 V/m.

The electric field strength (E) between two parallel charged plates can be determined using the formula:

E = V / d

where V is the potential difference (in volts) between the plates, and d is the distance (in meters) separating them.

In this case, the potential difference V is 18.0 V and the distance d is 3.50 cm. First, we need to convert the distance from centimeters to meters:

d = 3.50 cm x (1 m / 100 cm) = 0.035 m

Now we can calculate the electric field strength:

E = 18.0 V / 0.035 m = 514.29 V/m

Find more exercises on electric field strength;

https://brainly.com/question/15170044

#SPJ1

Answer:

The specific heat capacity of water is 4.184 J/g°C, and we need to find the amount of heat required to raise the temperature of 10 kg (or 10,000 g) of water from 20°C to 100°C.

The formula for calculating the amount of heat required is:

Q = m * c * ΔT

where:

Q = heat energy (in Joules)

m = mass (in grams)

c = specific heat capacity (in J/g°C)

ΔT = change in temperature (in °C)

We can start by calculating the change in temperature:

ΔT = 100°C - 20°C = 80°C

Then, we can plug in the values and solve for Q:

Q = 10,000 g * 4.184 J/g°C * 80°C

Q = 3,347,200 J

Therefore, Peter needs 3,347,200 Joules of heat to raise the temperature of his 10 kg vat of water from 20°C to 100°C.

Answer & Explanation FROM YOUR TEACHER:

The blocks does not have the same amount of thermal energy

The mass and temperature of an item are both inversely correlated with thermal energy. Thermal energy is expressed as follows:

Mass times Specific Heat Capacity times Temperature equals thermal energy.

where the material's specific heat capacity relates the amount of heat required to raise a unit mass of the material's temperature by one degree Celsius.

Even if the two blocks are at the same temperature, they will have different quantities of thermal energy since they have different masses. Assuming they are both composed of the same material and have the same specific heat capacity, the block with a mass of 300g will contain more thermal energy than the block with a mass of 33g.

33g × specific heat capacity x 175°C Equals 33g thermal energy of a 33g block.

Heat capacity of a 300g block is equal to 300g times 175°C in terms of thermal energy.

The thermal energy of the two blocks will vary since the masses are different.

1.) The sum of the forces in the y direction acting on the crate is given by the equation: F_y = m2g - T, where m2 is the mass of the crate, g is the gravitational acceleration (9.81 m/s^2), and T is the tension force.

2.) The acceleration of the block is given by the equation: a = F/m2 = 659 N / 53 kg = 12.4 m/s^2.

Here you can learn more about acceleration

https://brainly.com/question/3046924#

#SPJ11

Answer:

The  reflected spot will appear to be closer than when  the aquarium was empty.

N1 sin θ1 = N2 sin θ2         N1 is in air and equals 1, N2 is greater than one

θ2 is measured from the vertical and the ray is less than θ1

The distance to spot is less so it appears closer

(Consider a spot directly below the pointer    L1 = N2 L2)

If N2 = 4/3 then L2 would be 3/4 L1

Answer:

240 μC

Explanation:

When two capacitors are connected in parallel, the effective capacitance is the sum of the individual capacitances. In this case, the effective capacitance is:

C = C1 + C2 = 2 μF + 2 μF = 4 μF

The charge on a capacitor is related to the capacitance and the potential difference across it by the equation:

Q = C × V

where Q is the charge, C is the capacitance, and V is the potential difference.

Using this equation, the charge on each capacitor can be calculated as follows:

Q1 = C1 × V = 2 μF × 120 V = 240 μC

Q2 = C2 × V = 2 μF × 120 V = 240 μC

Therefore, the charge on each capacitor is 240 μC.

The increase in internal energy of the tie and spike is approximately 1.12 Joules.

The initial kinetic energy of the spike is:

K_i = (1/2) * m * v^2

K_i = (1/2) * 0.60 kg * (1.8 m/s)^2

K_i = 1.94 J

The amount of kinetic energy that is absorbed as internal energy is:

K_absorbed = 0.578 * K_i

K_absorbed = 0.578 * 1.94 J

K_absorbed = 1.12 J

Thus,the value is 1.12 Joules.

Kinetic energy is the energy an object has because of its motion. If we want to accelerate an object, then we must apply a force. Applying a force requires us to do work. After work has been done, energy has been transferred to the object, and the object will be moving with a new constant speed.

Kinetic energy is the energy of motion, observable as the movement of an object or subatomic particle. Every moving object and particle have kinetic energy. A person walking, a soaring baseball, a crumb falling from a table and a charged particle in an electric field are all examples of kinetic energy at work.

For such more questions on internal energy:

brainly.com/question/30702359

#SPJ11

Answer:

Explanation:

Fnet = ma = (270 kg)(2.3 m/s²) = 621 N

Fnet = F-forward - F-resistance

a)  F-forward = Fnet + F-resistance = 621 N + 450 N = 1,071 N

b)  Fnet = F-forward - F-resistance = 1071 N - 450 N = 621 N

The distance covered by the body after 15 seconds down the inclined plane is approximately 1102.5 meters.

We can use the equations of motion to solve this problem. The acceleration of the body down the inclined plane can be found using trigonometry:

a = gsin(30°) = (9.8 m/s²)(1/2) = 4.9 m/s²

where g is the acceleration due to gravity.

Using the equation of motion:

s = ut + (1/2)at²

where s is the distance covered, u is the initial velocity (which is zero in this case), and t is the time taken, we can find the distance covered after 15 seconds:

s = (1/2)4.9(15)² = 1102.5 meters

Therefore, the distance covered by the body after 15 seconds down the inclined plane is approximately 1102.5 meters.

Learn more about equations of motion:

https://brainly.com/question/30459518

#SPJ4

After the brakes are applied it takes 8.47s  time elapses before the toolbox strikes the cab.

The pickup truck is moving at 25 m/s with the toolbox of mass m resting on the bed of the truck 3.5 m behind the cab and the coefficient of kinetic friction between the toolbox and the bed of the truck is 0.3.

By using the equation a = (μk * g) / m

where a is the acceleration,

μk is the coefficient of kinetic friction,

g is the acceleration due to gravity (9.8 m/s2), and m is the mass of the toolbox.

By substituting the given values, we find the acceleration of the toolbox to be

a = (0.3 * 9.8) / m = 2.94 m/s2.  

Since the toolbox is initially at rest, the velocity at which it strikes the cab is equal to the final velocity of the truck, 25 m/s. To find the time it takes for the toolbox to reach the cab, we can use the equation

t = vf / a where t is the time, vf is the final velocity, and a is the acceleration found above.

By substituting the given values, we find the time it takes for the toolbox to reach the cab to be

t = 25 / 2.94 = 8.47 seconds.

Therefore, the time it takes for the toolbox to strike the cab after the brakes are applied is 8.47 seconds.

To know more about Time refer here :

https://brainly.com/question/1816510

#SPJ11

Displacement includes direction, distance does not

is your answer. hope it helps!

the block when it is being hauled up the slope at a constant speed using force F perpendicular to a ramp, with a force of 10.0N.

Force is indeed a physical phenomenon that alters or has the potential to alter an object's shape, its state of motion, or both.

According to Newton's second law of motion, the force corresponds to the momentum change divided by the time change. Force equals mass times acceleration, or F = m x a, for a constant mass.

To know more about force visit:

https://brainly.com/question/30526425

#SPJ1

The volume of water in the bowl is then:

v = (2/3)π(38)^3 - (1/3)π(h - 4)^2(3h + 8) - 256π/3 Case 1: The ball is not completely submerged

The volume of water displaced by the ball is equal to the volume of the ball. The radius of the ball is 4 cm, so its volume is (4/3)π(4)^3 = 256π/3 cm^3. The height of the water in the bowl is h - 4 cm, where h is the total height of the water and the ball. The volume of water in the bowl is given by the formula for the volume of a hemisphere with radius 38 cm minus the volume of the spherical segment cut off by the water level: v = (2/3)π(38)^3 - (1/3)π(h - 4)^2(3h + 8). The volume of water in the bowl is then:

v = (2/3)π(38)^3 - (1/3)π(h - 4)^2(3h + 8) - 256π/3

Case 2: The ball is completely submerged

In this case, the volume of water displaced by the ball is equal to the volume of the ball. The height of the water in the bowl is h, so the radius of the water level is (38^2 - 4^2)^(1/2) = 37.83 cm (by the Pythagorean theorem). The volume of water in the bowl is then the volume of a spherical cap with radius 37.83 cm and height h, minus the volume of the ball:

v = (1/3)πh^2(3(37.83) - h) - (4/3)π(4)^3

Note that the volume of the ball is the same in both cases, but the volume of water in the bowl is different.

To learn more about volume refer to:

brainly.com/question/1578538

#SPJ4

(a) The tension in the hitch is 339.75 N.

equal to the mass of the trailer times the acceleration (453 kg x 0.75 m/s2 = 339.75 N).
(b) The force of static friction exerted by the road on the pickup truck is  1038.75 N.
(c) The force the trailer exerts on the pickup truck is equal to 339.75 N.

(a) The tension in the hitch is equal to the mass of the trailer times the acceleration.

It is calculated by,

453 kg x 0.75 m/s2

= 339.75 N.

(b) The force of static friction exerted by the road on the pickup truck to propel it forward is equal to the mass of the pickup truck times the acceleration

It is calculated by

1385 kg x 0.75 m/s2

= 1038.75 N

(c) The force the trailer exerts on the pickup truck is equal to the mass of the trailer times the acceleration.

It is calculated by,

453 kg x 0.75 m/s2

= 339.75 N

Static friction is a force that keeps an object at rest. Static friction definition can be written as: The friction experienced when individuals try to move a stationary object on a surface, without actually triggering any relative motion between the body and the surface on which it is on.

For such more questions on static friction:

brainly.com/question/13680415

#SPJ11

The wave drag coefficient, C_D,w, is a component of drag experienced by a vehicle during supersonic flight and is defined as the ratio of the wave drag D_w to the dynamic pressure q_infinity times the reference area S. This wave drag is a result of the shock waves created by the vehicle travelling at supersonic speeds, and is governed by thermodynamic properties such as specific heats at constant pressure (C_p) and constant volume (C_v).

The ratio of these two specific heats, C_p/C_v, is equal to gamma, and with the use of Buckingham's pi theorem, C_D,w can be expressed as a function of M_infinity and gamma. Friction can be ignored due to the supersonic speeds of the vehicle.

To express C_D,w as a function of M_infinity and gamma using Buckingham's pi theorem, the independent parameters of the problem must first be identified. The independent parameters of this problem are the Mach number M_infinity, the reference area S, and the ratio of the specific heats C_p/C_v, also known as gamma. With these identified, the dependent parameter of C_D,w can be expressed as a function of the independent parameters by constructing a dimensionless group or pi group.

The pi group for C_D,w is formed by the multiplication of the independent parameters. For example, the group can be expressed as (M_infinity * S * (C_p/C_v)). This group can then be rearranged to C_D,w = f(M_infinity * S * (C_p/C_v)). Since gamma is equal to the ratio of the specific heats, the pi group can be simplified to C_D,w = f(M_infinity, gamma). This shows that C_D,w is a function of the Mach number and gamma, and that friction can be neglected.

Know more about shock waves here:

https://brainly.com/question/30835673

#SPJ11

Volcanic activity and the movement of lithospheric plates both result in the formation of new mountains.

Volcanic activity can include the release of gases, pro lava emissions, or extremely ferocious explosive bursts that can last for several hours. Volcano shapes and sizes are influenced by eruption type, which also affects the relative volumes & types of lava flows and volcaniclastic debris.

Worldwide repercussions would result from another big caldera-forming eruption at Yellowstone. The repercussions of such a large eruption would be felt locally and include ash fall and short-term (decades to years) changes to the global climate.

To know more about volcanic activity visit:

https://brainly.com/question/30513717

#SPJ1

Answer:

Place the thumb of your right  hand in the direction  of the current and the fingers will be pointing "upwards" - this is handy for long straight wires

Answer:

(C) it is moving to the right wrt to the ground

The crate is accelerated to the right (wrt the ground) because the frictional force between the truck bed and the crate is to the right and it is this force that provides movement to the crate

Answer : a) The crate will be moving in the negative x direction (to the left) when it falls off the truck. The force of the acceleration of the truck in the positive x direction will push the crate in the negative x direction. This will cause the crate to move away from the truck in the negative x direction. Correct answer is option B

This is because the truck is accelerating in the positive x direction (to the right), and the crate, being free to move, will have the same acceleration as the truck. This will cause the crate to slide backwards off the truck in the negative x direction.

Therefore, the crate will be moving in the negative x direction (to the left) when it falls off the truck.

Know more about friction here:

https://brainly.com/question/13000653

#SPJ11